Search results

I have 2011 gt, about to order 20x9 and 20x11(55 offset) forgestar f14 looking to put 275/35 nt05 on front and 315/35 nitto nt05r on rear. i want it slammed. i was looking at h&r super sports with adjustable panard bar, had them on past mustangs and liked the drop. im just worried i might rub on...

I have 2011 gt putting on h&r ss springs , ordering vossen cv7 20x9 and 10.5 I want a sticky rear tire for the rear to hook the twins, I looked at nitto nt05r 315 35 20 for rear with some nitto nt05 in front. Worried if it will clear the 315 35 in rear with the h&r ss? Any recommendations front...

2003 Black Cobra 83,xxx miles Car runs and drives great-just looking to buy another toy. no trades or test drives(unless money put down). Exterior: new HID Headlights and fog lights fore hood vents smoked head lights tinted taillights tinted windows. 18x9 and 18x10.5 front tires are...

I recently removed my dragon throttle body/plenum due to idle issues, installed new accufab, and changed filter on RAI to amsoil, now getting whistle/vacuum leak noise when first starting up and when you let off gas you can hear whistle, i have heard accufab or most aftermarket throttle bodies...

I recently installed ss lines, installing the right rear, when i took off factory one seemed like it was overtightened to begin, when installing new ss one i had a little trouble but got it, installed it, test drove, and looked at each line to make sure no leaks or anything, noticed real small...

I was installing pump and no movement of fluid so i did what it said in the how to section -sucking on the top line to reservoir, i get little fluid while pump is jumped, but then i keep trying and now when i try to jump you dont hear pump or anything-did i lock up new pump or what?

I am removing my steeda springs from my car , installed front fine, rear i dropped catback, removed low pro bolts dropped irs, rear springs fell out, installing new h&r sports no isolators, i placed them in, everytime i tried to lift rear subframe up, i just lift car off stands, i took springs...

How much coolant do you use when installing one of these? with afco heat exhanger, same as factory? i tried searching and could not find clear answer

ordered bilstein hd struts for my cobra, so i got them and removed old ones and the cover for shaft has bump stock integrated and the new one is just the normal blue boot, Im guessing i just use the one off the orginal strut, Is that correct?

I have spec 3+ clutch 10 spline, billet still flywheel, new tob, lethal tob sleeve, fiore fire wall adjuster and blue 3 hook quadrant(came on car), new stock clutch cable, problem is im on middle hook, properly adjusted tob/pressure plate, clutch releases all the way at top, so i decided to get...

I ordered new motorcraft battery cables on line and they say they fit cobra, but in the wiring harness there is no wiring for alternator, im thinking i got a normal 4.6 one where the alternator is in different location, anyone had any problems or ordered the right cables could chime in and help...

I wired up a whistler radar detector that has wireless transmitter in bumper and reciever in car i recently installed hid's for fogs and headlights, now when i turn on hids the radar detector says communication error-at first i thought to re wire radar detector didnt work. so i started...

Anyone know where i can get some of these?

i am wanting to put some 03 cobra wheels on my car, jsut wondering if you guys run 17x9 all the way around or if i can run 17x10.5 in the rear?

My buddy is looking to put new cobra motor in his gt but he is saying the guy who is selling the motor says it has no miles and was made this year but still has forged internals? i thought they do not have forged internals anymore?

i have 18inch afs wheels and i usually clean with soap and water then use mothers chrome polish and remove with microfiber, i dont know if there was dirt on microfiber or they are just junk microfiber and now on two wheels i have some fine scratches, Any ideas on how to remove or make less...

FIRST WHAT I HAVE DONE ON CAR SUPERCHARER WISE 2003 Cobra STEGE STG 4 PORT BILLETFLOW IDLER SET BILLETFLOW 2.76 3.2 ALT METCO 4LBS LOWER RECENTLY INSTALLED UPR TENSIONER BELT THAT I HAVE ON CAR : GATOR MICRO-V AT K080797 I was out driving earlier just me and my lady friend,i got on it...

i have this noise and i hope it nots TOB because it has less than fifty miles on it, when i go to push clutch pedal in it squeaks, car has brand new TOB 50miles or less, new clutch cable, spec 3 + clutch, lethal TOB sleeve, fore firewall adjuster and upr quadrant. ANy ideas would help?

Like the title says i ordered new clutch cable i installed it and it doesnt want to sit flush on the firewall adjuster any ideas? i thought maybe the piece of clear tubing that goes over black piece of cable is to long but not real sure what to do, i can move cable around to make it work but...

I just removed junk spec TOB installed new one, adjusted clutch to what my buddy thought was spec, driving around block after i burp coolant and everything is good then i drive little further and push clutch it and its chirping again, i have some shitty blue adjuster,triple hook quadrant, dont...

i took off my jlt ram air intake to install dragon throttle body and plenium,there is oil in the intake tube. What does that mean? do i need to look into oil separator or is something wrong?

I just replaced leaking oil cooler and oil filter adapter, i tightened on oil pressure sensor put oil in and found small leak coming from adapter housing where it cracked reinstalling sensor, so i ordered another one, but how tight do i go i did not think i went that tight last time

I am about to order billet specialite street lites 15 inch front with 165 tire, and in the rear 16in x 9.5, i dont want very much rake in the stance, car has steeda springs with no isos in the rear. Which tire size do you recommend?

I have heard of using coke method to remove but how do you prevent it? i know dumb question and i did search.

I am having issues with trying to remove the stock studs as one has came out when i took off my flow tubes. I bought replacement studs and they are a bitch to put in. Anyone have any tips or tricks to put these in as i have become to frustrated to continue with this tonight.:shrug: