Search results

Yo...what a close one! A couple of weeks ago I was following a guy on one of the 2 lane blacktop roads in the Bremerton area. This guy was anywhere from 5-10 miles an hour below the speed limit for about 10 miles. Finally there was an opening to pass so I pulled into the other lane, down...

Unfortunately the Washington State Senate just passed the "California Emissions Standards"!!!! :cuss: :cuss: :cuss: :cuss: :cuss: I have a 98 Cobra and have recently installed a KB blower. I want to install the KB CAI, but my Cobra has that damn smog unit located in the right front...

I was in the process of ordering a cold air kit for my 98 Cobra? When I took out the stock air filter cannister and looked through the large whole of the fender well I saw a rubber hose extending up with a rubber cap. It, as well as another hose or 2, plus a couple of smaller lines go into a...

I am installing a fuel pressure and boost gauge. I was going to splice the "light" positive wires into the stock light positive wire so the dimmer would also work on the 2 new gauges. Does anyone know what color the positive light wire is for the 98 Cobra? Or, do you recommend splicing to a...

Until I get my car dynoed to see if the new KB blower/chip is functioning properly, I am adding a little octane booster to my gas. They say it changes the color of the plugs. The change of color does not concern me...does the octane booster cause any other problems? :shrug: Thanks!

Does anyone know how the newly adopted Washington (California inspired) State emissions law :cuss: will affect us? :fm: :fm: :fm: :fm: :fm:

On my 98 Cobra, there is a sensor located on both exhaust pipes about 1 1/2 from where they bolt to the stock headers. What are these sensors for and do the Bassani catted "x" allow for these sensors?

Here is a pic of where I notched the hood liner and a piece of the fiberglass. Using the template provided by KB, I first traced the pattern onto the hood liner (I purchased a new hood liner so that I would not have to cut the original) and using a dremmel, cut just the liner. I then marked...

I want to make sure the KB chip is providing the correct A/F mixture.... where is a reputable place that can check it out? I live in the Silverdale area... Thanks!

Here are some pics ya'll asked for...

Here are some pics ya'll asked for...it purs at idle and roars when needed! :banana: :burnout:

Here are some pics ya'll asked for...it purs at idle and roars when needed! :banana: :burnout:

The weather in the Seattle area cooperated, the doors of the shop opened, and my final fears were put to sleep. She idled smoothly at 750 rpm's.... at only 3/4 throttle the rear tires would break loose and the rear end would go what ever way I wanted it to... I fealt no engine hesitation...

The weather in the Seattle area cooperated, the doors of the shop opened, and my final fears were put to sleep. She idled smoothly at 750 rpm's.... at only 3/4 throttle the rear tires would break loose and the rear end would go what ever way I wanted it to... I fealt no engine hesitation...

Due to illness I was not able to spend the time I wanted on the project, but I finished it!!!!! Turned the key 15 minutes ago and it fired right up! :pepper: :banana: :pepper: :banana: :pepper: I was a little nervous when I turned the key, what a relief when it roared; what a great...

Due to illness I was not able to spend the time I wanted on the project, but I finished it!!!!! Turned the key 15 minutes ago and it fired right up! :pepper: :banana: :pepper: :banana: :pepper: I was a little nervous when I turned the key, what a relief when it roared; what a great...

Due to illness I was not able to spend the time I wanted on the project, but I finished it!!!!! Turned the key 15 minutes ago and it fired right up! :pepper: :banana: :pepper: :banana: :pepper: I was a little nervous when I turned the key, what a relief when it roared; what a great...

98Cobra/KB...FMU location? No possible way will the FMU will fit where the instructions and picture says it will; fittings do not clear stock CAI, much less with the hoses attached. Did I fail to read one of the instructions....anyone else have that problem? Any problem with placing the FMU...

98Cobra/KB....FMU location? No possible way will the FMU will fit where the instructions and picture says it will; fittings do not clear stock CAI, much less with the hoses attached. Did I fail to read one of the instructions....anyone else have that problem? Any problem with placing it above...

I posted this in SN 95, but thought I would post here as well: I had a good feeling last night when I finished all of the engine work on the KB install; all I have left is adding the chip and BAP. Sometime during the night my eyes suddenly openned realizing I had not cleaned the butterflies...

I had a good feeling last night when I finished all of the engine work on the KB install; all I have left is adding the chip and BAP. Sometime during the night my eyes suddenly openned realizing I had not cleaned the butterflies on the IMRC! Although they were not gummy, I had planned to clean...

Some guys asked for pics of KB install in progress. Here they are: http://www.svtperformance.com/forums/showthread.php?t=171311

Some guys aked for pics so I posted them on the Cobra forums. Go to SN95 Cobra's, click and you will find the post with the install pics. http://www.svtperformance.com/forums/showthread.php?t=171311

For those who were asking and those who may enjoy. :beer:

Just got my KB last night. When I was looking through the instructions I saw where you had to make a small cut in the hood liner as well as cutting some of the metal hood support bracket. I do not mind cutting the liner, but I don't like the idea of cutting the metal. I was wanting to keep this...