I have a 2004 mystichrome cobra from new and have just finally had my first severe scratch put on...
I am trying to find the g6 paint at this point as I am going to purchase a new tekna prolite paint gun to spray...
I have not found the paint but leads have me going to Napa up here in Canada...
Hello all
I am considering going with the quiet borlas or steedas to quiet down my setup.
Right now i have the kooks lts, catted xpipe and stingers.
I am not sure how loud magnaflow is but i think the quiet borlas are my best bet.
Anyone with quiet borlas care to chime in?
Thanks
Hey everyone
Right now i have kooks LTs kooks catted xpipe and borla stingers . The car is LOUD and the ears are taking a hit especially the left one.
Does anyone know where to get the QUIET borla/steeda mufflers or part numbers so i can just weld them in place of the stinger cans?
Thanks
just wondering if this smoke is normal coming from the exhaust.
I dont beat on the car but when it was strapped down it spit out some smoke.
95SHO.flv video by sho95 - Photobucket
Hey guys, sorry to bring this back to attention
first off this has nothing to do with the stall flash update needs done from ford.
When driving the car and not abusing it and putting the car into neutral coming to a stop the rpms will start to bounce and sometimes the car will stall or if you...
I think i may have an exhaust leak.
right around 3500 it flutters a bit when i shift and the rpms drop.
Does anyone have special tips to seal them up or special tools that i may need in order to get to the bolts? Any special ways to get access to them or write ups somewhere?
Thanks guys
Just trying to get a feel if anyone is close to or in Ontario Canada that might want to trade catbacks. My stinger for a newer quiet borla.
Not sure how much shipping would cost going to the states and how to package it so i would like to try for a semi local trade if possible..
Thanks
OK guys need your help
I bought a D&D input shaft figuring it would come the same as a liberty but it did not.
It is missing the bearing that meets with the casing. If i had of known this i would not have bought it and waited for the liberty.
Does anyone know where i can get the bearing or a...
I have a new block
Newest revised heads
ported blower& TB, 2.93 up top 4# lower, all idlers, 2400 SCT maf, GT pumps, modified FPDM.
I do not have the tick if the car is just sitting with the engine on. I can rev the car and not have the tick
When i drive the car it is another story which...
Hello all
I am just wondering if I still need a BAP with a modified FPDM and twin GT pumps?
I have the BAP on my stock pumps and FPDM currently but pumps are dead.
I am only running a ported blower with 2.93 and 4 pound lower.
60# injectors
Kooks headers xpipe and stingers
sct 2400 maf...
Car is having issues with low fuel pressure which may be causing lean conditions and is causing idle problems. dealership said fuel pressure shows 11psi
My question to you is do you think it is the fuel pump or would you consider it may be my BAP that is faulty if its possible or what else...
Getting some motor work done to my car and while it is apart they said they would put the aftermarket headers on at no cost.
I am thinking of Kooks headers and either a kooks catted x pipe or magnaflow catted x into my borla stingers.
Now my question is, will the magnaflow xpipe fit up with...
I would like to hear the full SS works exhaust headers all the way back.
I am thinking about going with headers and might as well get the complete kit.
Thanks
I have just started to get this whistling sound while the rpms climb (not under hard load)
The noise sounds like amplifier interference when you install an aftermarket sound system and you can hear it through the speakers. My noise is coming from the front of the car though and not through the...
I am thining about going this route. I have the stingers already and was thinking about getting the magnaflow catted X. Just wondering on opinions or if anyone has a vid to check out first?
Looking for opinions on my numbers
Mods are
STIEG ported blower
billetflow 2.93
metco 4# lower
all billetflow idlers
metco 3.2 alt pulley
60# injectors
NGK TR6 gapped at 33
BAP
SCT2400
XCAL2 tune
91 Octane tune
Boost hit 18# and then dropped to about 16# higher in the rpm...
I know this is being debated right now with all the alternator issues.
I am doing a 2.93 4# lower and 3.2 alternator pulley with a Steig stage3 port soon to arrive at my house.
Is the 3.2 alternator pulley safe to run with this combo. What will happen if it is not? or should i stick with the...
I just got off the phone with Billetflow. Bought some pulleys
I just purchased
2.93
4#
3.2 alternator pulley
3-100mm idlers
1-92mm idler and bracket
I was just wondering what belt i would use for this combo?
Thanks
Hey all
I was going to drive down to Missouri to have the blower ported but now with gas prices and all I may just ship mine down. How much will it cost with shipping and duty? Any other info would be appreciated.
James