Search results

I need to replace my two front engine mounts and the transmission mount. I have the ford OEM mounts and the Harbor Freight engine support beam. Any advice or suggestions before I dive under the car? I was planning on removing the exhaust, and disconnecting the old mounts, then using the...

On rt 93 in MA you are allowed to drive in the breakdown lane during rush hour time periods. I was driving home today and was in the breakdown lane @ 255PM. I normally drive home between 4 & 5 PM and never think twice about it because all the traffic seems to migrate to the left lanes. Today...

I may have inadvertently thrown out the drain plug on my ford racing IRS cover. Anyone know the diameter and thread count? Thanks Mike

I may have inadvertently threw out my "drain plug" on my ford racing IRS diff cover. Anyone know the diameter and thread count? Thanks for looking Mike

I have an extra Ford Racing Reinforced IRS Rear Diff Cover including mounting hardware. It is installed on my spare IRS case. 500 miles at most on the cover. All the best Mike

Anyone ever have a local machine shop install dry sleeves in a teksid block and build a high quality motor? Thinking of a NA engine build and 3.7" bore is well worth it but I do not know anyone who is living with such a combination. Anyone use "LA Sleeves" in their build? Thinking of 3.7"...

My driveshaft on my 1999 Mustang Cobra is toast. Any local shop recomendation around southern NH? The original shaft has a little bend in it and can not be re-balanced. I contacted Brookline Machine in North Andover they wanted $520 plus my old Yoke's. PST will send me an aluminum...

Dam anyone know where I can get another oil cooler insert stud? It holds the oil cooler to the block and is the stud that you use to screw in your oil filter. Plus it has an O-ring on the stud that keeps the coolant and oil seperated. Ford no longer makes them..... Thanks for the help

I recently replaced all of my IRS suspension bushings and am in need of a solid 4 wheel alignment. Car has Steeda springs Bilstien shocks and MM CC plates. I usually go to Townfair Tire in Plaistowe NH. They do a good job on all my cars, I was just thinking of trying a shop that would take...

I am rebuilding my IRS this winter/spring and one of the last items I had to do was replace the bearing inside the passenger rear suspension knuckle. I dropped the knuckle and new bearing off at a local Ford dealer on Thursday and picked it up about four hours later. I went to install it today...

Ok the time has arrived to upgrade my IRS bushings. I have the car safely supported. Everything that needs to be removed is (calipers, antilock brake sensors, parking brake cables etc.). The car currently has 16.5” clearance from the lowest point on the inboard LCA to the floor in my garage...

I am add a new ford racing cover to the IRS on my 1999 cobra. While the diff is out I was going to upgrade the clutch pack on my stock 1999 28 spline traction lok diff. My question is will the carbon clutch kit's 31 spline preload spring fit in the space available in my 28 spline diff...

I have two OEM 28 spline half shafts for sale. They were recently taken off my 1999 Mustang Cobra. One has 50k miles of normal usage. The other was hyperextended and needed to be remanufactured by A1 Cardone in Texas. This remanufactured axle has not been installed yet and is still in the...

I have two OEM 28 spline half shafts for sale. They were recently taken off my 1999 Mustang Cobra. One has 50k miles of normal usage. The other was hyperextended and needed to be remanufactured by A1 Cardone in Texas. This remanufactured axle has not been installed yet and is still in the...

I need a 28 spline 1/2 shaft for my 1999 Cobra. My drivers side unit finally expired. Cheers

My 1999 Cobra's diff cover threw in the towel last night at the track. Housing may be toast and I know I snapped the drivers side halfshaft too. Ooo well upgrade ideas? Only 345@ the rear wheels.

Anyone ever try Granatelli Hot Street Coil packs? They are rated for 45K volts stock is 20k volts. My car has 50k miles on the stock coils so I can't imagine I am anywhere near 20k volts. My car has all of your typical bolt-ons. Cheers

I want to see if Cobra R Brakes will fit my stock 99 wheels. I searched several forums and found that the 17" wheel is not a problem but I need to have 50mm (1.97 inches) from the rotor to the back of the wheel. I just checked my wheel and it looks like I have 2 inches at the outside edge of...

Does anyone know the name of the company(s) that provided the upholstery kits for Saleen or Roush Mustangs? I tried searching several forums but came up empty. Thanks for the help. Cheers

Any have a new 35th aniv instrument bezel laying around? Mike

Anyone have a 35th aniv. instrument bezel collcting dust? Mike

I will be installing long tube headers along with an IRS bushing upgrade over the next several weekends. What are the best jackstand placement options? I could easily support the car with four jackstand's using my subframe connectors welded attachment points but I have seen photos with the...

Changing brake fluid for me is always a two person affair. Has anyone ever used Russell or Earls speed bleeders? This seems like an inexpensive mode that can really cut down the time necessary to change your brake fluid. How about the Speedi-bleed tool? Here is a link. Speedi-Bleed –...

Well I was sitting around the kitchen waiting to begin another round of snow blowing when I started thinking about a small project to perform on my sleeping Cobra. Well the instrument lights have never really been bright and the color is a little flat (maybe the bulbs are just showing their...

What is the best cleaner to use for your carpets? Something that is not heavily scented would be ideal. Every cleaner I have used has an overwhelming perfume that takes months to disperse. As a result I neglect my floors and mainly just vacuum regularly and spot treat as required. Has...