Recent content by svt4cobra6

I am in Calif as well, original owner 2003 cobra. Still on stock tune, just have cold air intake and exhaust, after reading this no plans to modify further.

a friend is looking at 2 used cobras, one is owned by an older guy still has stock tune, records of oil changes and stock pulley but does have a cold air, shifter, mid pipe and catback, well maintained looks and drives like new but has around 60k miles. My friend said the other cobra has a...

I have an 03 cobra with mrt catted hpipe, mag catback and K and N fipk, just wondering how it would do against an 03 saleen that I think came with the m90 Eaton? There is a guy that wants to race but I am thinking I might need at least a pulley and tune with the weight disadvantage as I still...

just wondering if anyone knows if installing a whipple supercharger on an 03 cobra will cause a visual smog check failure in california? I have a 2000 f150 that is completely stock but had a section cut out of the stock plastic airbox and they failed me on the visual, of course this was the...

Hi I have a 91 mustang notchback with a 351w with all the smog equipment as well as a high flow catted pipe. Just wondering if this will pass calif smog, passed fine in Nevada, thanks.

I have a 2000 f150 supercab with the 5.4 and will be doing some towing. I tried to see if it has a factory tow package, it has a class 3 hitch and a connector about 5 inches to the right of it. The connector has a cap and looks like it accepts a round connector. Also I am thinking of...

I am moving from Nevada to California and have an 03 cobra. Still has stock tune and pulley but aftermarket catted hpipe and catback as well as a cold air kit, should this pass calif smog ok? Also does calif require a front license plate and if so any way to mount it on to the bumber without...

this seems like a pretty big blower for a daily driver, just wondering if running 13 lbs with the wipple 3.4 can you still use the stock fuel system and any estimate on power with cold air, high flow catted h pipe, and catback. thanks.

Just wondering if anyone could provide details on how to replace the inner belt that goes arount the water pump, 03 cobra? I did a search but only found replacement of the supercharger belt which takes just a few minutes. I have the stock pulley set up, thanks!

I have an 03 cobra that is going off of warranty in a few months, 64k miles and I drive it about 25 miles a day. Just wondering if a chip and pulley would effect gas mileage when driven easy and are there too many miles on the motor now, seems to run just like new. Also I would get the heat...

I have oil leaking from the back of the engine where the trans attatches. The motor is stock but has 61k miles (03 terminator). I can not tell exactly where it is comming from but just wondering if the oil pan gasket or rear main seal could be bad and if it is difficult to replace it? thanks

Hi looking for a price quote for 2 tires shipped to Las Vegas, NV, size 275/35 or 40/17 either nitto 555 extremes or Yokahoma S drive tires. Thanks.

I just purchased 4 FR500 black rims 17x9 and 17x10.5 used for a good price. All of the rims have nitto drag radials, even the front. The wheels and tires fit good (no IRS bolt inteference) but I am wondering if it is safe to run drag radials on the front? It is pretty dry out here, Las Vegas...

I was just wondering if anyone has been running more than 550hp for a long time and not had any engine problems? I read in MMFF (an article by a mod motor expert) stated that the 03-04 cobra motors are good up to about 550 hp (for motor longevity). If that is the case maybe a stock ported...

triax shifter, pro 5.0 handle, currently at $37 on ebay, plus shipping.