Search results

I mounted my Fore regulator in the passenger wheel well. I have all stock vacuum lines/emissions, etc with a Gen 2 2.9 Whipple. Anyone have some pictures of where you t'd in for vacuum? I have dual 525 pumps and if I decide to mount the Hobbs switch I can t in behind the glove box I believe for...

Looking for a gently used set of 17x10.5 chrome 03 04 cobra wheels. I live in NH and will travel within reason unless you are willing to ship. Thanks.

I am looking into a return system. I currently have a gen 2 2.9 Whipple non crusher. Will be upgrading blowers most likely when I do fuel system to a new version 2.9 crusher or the 3.0 version. I know I need ID 1300's (Currently have ID 1000's), dual 465 pumps, FC3 controller. Dead head vs other...

Does anybody have a source for the o rings on the coolant ports on the rear of the cylinder heads? I have a LDC kit, but I would assume the o ring is the same for all kits? Thanks.

Has anyone found a source for the OEM Oil Cooler? I am looking for an OEM NOS one...would be willing to pay a fair price. Even though my engine did not have a bearing failure he does not want a used oil cooler going back on. Relocation kit is not an option. Ford 2R3Z-6A642-AA

Friend of mine has a Foxbody with a 5.8 gt500 motor and a 4.0 whipple. Tuned by Lund Racing. Had shop do the conversion for and they did pulls on dyno with brand new crate motor. Best reading they could get due to tires breaking loose was 650rwhp on a "Safe" break in tune. Drove it for a bit and...

2003 Cobra. Mods are: 93 octane with Torco. Been using this fuel for years. 2.9 Whipple 3.5 upper 4lb lower. K&N air filter stock intake tube. Accufab throttlebody. Id1000 injectors. ARH 1 7/8 Headers 3" X Pipe 2.5" Bassani catback with baffles. Ford GT Pumps with 2 FPDM's in a Fore hat. Car...

Removed from 2008 GT 500. Wheels are like new with no damage. Local pick up only. Front tires are 255/35/zr20. Rears are 295/35/zr20. Have less than 1000 miles on them. Set includes Ford TPMS Sensors. $1500 for the set. Please call or text 978-996-Three Zero Seven Two if interested.

What are you guys using for seat covers on your cobras? How do they fit and can you post pictures? Thanks.

I have had a metco 4lb lower for 8 years now. Never had any problems. Now have 2.9 whipple with 3.5 upper pulley. 24lbs of boost. Stock tensioner. Am I in danger of breaking the crank? When I install longtubes the boost should drop a couple pounds. How many documented failures have their...

Anyone have sound clip of ARH 1 7/8 headers 3" x pipe 2.5" Bassani Catback? Or something close to it? I'm coming from UPR X Pipe no cats and 2.5 Bassani catback. I don't like the tinny raspiness. Before I spend $1500 on the ARH set up just want to see how it will sound.

Tremec 6060 for 07-09 gt500 18k miles . Perfect condition will fit any mod motor . Comes with SVT Short Throw Shifter. $1500 firm For more info call or text 1 978 Nine 9 6 3 Zero 72

Looking for more clearance for long tube headers. Will be using stock springs/struts. Is there a K-member/control arm combo that will accept the stock springs? Or even stock a-arms? Wishing the Maximum Motorsport one didn't move the wheels forward.

Posting for a friend who is not to forum savvy. The car is a Sterling Gray 2013 Shelby GT500 with 4000 or so miles. Has Recaros, Nav, Factory Car Cover, 3:73 gears, Ford Racing Throttle Body. Car is essentially like new. The price is $49,999. Please send me a PM and I will give you his phone...

What pads should I use to polish stainless? It's for a stainless dump body on my new 550. I have a porter cable with the big and small pads. Or would a ball on a drill be better to get in the small areas? What polish works good also?

What brand and size long tube headers are people running? Stock k member. What brands tend to fit the best? Will my fuel system be enough? Currently 2.9 whipple, 3.5 upper 4lb lower. 24.75 lbs of boost. Was going to go long tubes and 3.00 or 3.25 upper. Fuel system is fore hat, gt pumps, 2...

Trying to isolate where this noise is coming from. Just installed a blower with no other changes. Fan spins freely by hand. Is there a way to jump the fan relay like I can with the intercooler pump? Any other ideas? Belt tensioner is in the middle so it's not that.

Has anyone dyno'd these combos? Is the Ram Air worth it over the stock tube with K and N? Just installed a Whipple 2.9. I like the stock look as it doesn't rub the strut tower like the C & L intake did. Have seen a bunch of others also rub the tower.

On the intercooler to blower bolts. Whipple says to use loctite. When I did the ported blower years ago I don't remember using red loctite or anything. Will I be able to break the red loctite in the future? I had a Dragon throttle before and had to get a iac valve that was rotated. Will I be...

Just bought a new 2.9 Whipple. Any chance someone would sell their revised Billetflow throttle body? Thanks. If I don't reply, send me a PM as I'm not always on here.

I may be buying a 2.9 Whipple and will have to put the lower pulley back to stock. I found my original alternator pulley but not the lower. If I can't find it does anyone have one? Thanks. Car has 18k miles and would like to find a low mile one if i can't find mine.

About to make the plunge to a 2.9 Whipple from a ported Eaton set up. Fuel system consists of Fore hat, GT pumps, dual fpdm's, wire upgrade. Maf has been upgraded as well. What throttle body will work on the Whipple? Other than a tune, what else will I need? Car has a 4lb lower pulley. What...

Anybody ever have problems with the intake tube falling off even when you tighten it down? Seems it like to slip off. Any tips or tricks?

Would like to order a new 450 xlt chassis truck. Is there anyone on here who would like to quote me on a truck? Send me a pm. Thanks!

Anybody have a link to the movie Fury? Just tried to click on one and a bunch of virus stuff came up.