Recent content by quadcam

Hooker Supercomp longtubes, Aerochamber o/r xpipe, NEW King Cobra clutch, NEW Fidanza flywheel, Densecharger CAI, Steeda Tri-ax, Eibach sportlines, 4.10s, Mickeys with about 30 miles on them- never raced. Front bumper has some flaking paint, has typical rock chips. 100k service package done at...

The shop called me today, and they've finally got the car figured out. The base dyno was 232rwhp because of the slipping clutch. After my initial tune, the car put down 260 some, I can't remember exactly what because the sheets arent' here now. The shop and I both thought those...

Last season, my car consistently ran 13.6's at 101-102, with the occasional 103 and one 105, all in 900' DA with 90-100+ degree temps last summer. All the car has done to it for power is a CAI, o/r hpipe, and a catback. Last week, I took my car in to get some stuff installed and to get an SCT...

Does anybody make one? All I can turn up for 94-98 is non Cobra covers. I had a minor fender bender and it's cheaper and easier in the short run to cover it up so I'm not embarrassed riding around with spider webbed paint until I can save up $400 to get the bumper fixed right. Thanks in...

I'm about to buy a new clutch and flywheel from Summit, and I've decided on the King Cobra FRPP clutch. I want to get a Fidanza flywheel to go along with it, and when I search for flywheels for a 97, all it comes up with is this, which it says is for an 8.5-9.5 inch clutch disc diameter. I'm...

I have a set of Hooker Super Comp longtubes and the matching Aerochamber catless xpipe that I had for my 97. I never got around to putting them on, and I'm not entirely sure that I wanna even keep my car anymore, so I'm putting this out there. These are used pieces, non ceramic. I would be...

I've scoured the internet, and I can't answer my own question. What I would like to know, is how many cars where offered in 03 (and possibly 04 even though I've never seen one) had the tan inserts? That is the key requirement for me when I start looking for my car, but it seems like it's an...

I'm looking to see some pics of those seats in an 03 Cobra. I'm really thinking about getting some when I get my Terminator next spring, and I would like to see some shots to see how they match up to the rear seats. I know they will, but it would just be nice to put eyes on. thanks!

I am planning on buying a Terminator next spring. I want to keep my car as stock as possible, but I still want to get 450-500 rwhp. Would it be possible to achieve my goal with a 2.6 KB running about 15lbs with nothing but a K&N drop in, a conservative tune and maybe a catback? After having...

Ok, I am a fairly competent backyard mechanic, but I've never tried anything of this magnitude before. I am utterly certain that I could do the install myself for a bit less than the 700-800 a shop is going to charge me even if I buy tools, and I was hoping someone on here could give me some...

Could I run a pair of resonators along side of my mufflers on my catless setup to suck out some sound but not lose any power? Forgive my ignorance. :bash: lol

I need a new clutch, and while I'm at it I want to go ahead and put a Fidanza flywheel in my car, and on Ebay Gripforce is offering package deals at what seems to be a pretty good price, but I haven't seen any 10.5 kits from them. If I needed to, could I go to an 11 inch setup as long as I had...

I'm thinking about using my tax returns next spring to throw forged rods and pistons into my car, and get the valvetrain refreshed. It seems that a decent quality set of pistons, rods, and the required supporting hardware will run me about $1200, and I figure that a basic valve job will cost...

Well I made it out to KCIR today, and only got in one run. I had what was for me a very good 60' (1.92 on bald tires), but my ET was way off, it was only 13.73 at 100.5. Normally I'm running 13.3-4 at 104-105. Would the crazy heat we had in the first half of the day be accountable for that...

If anyone has one that they want out of their garage and will send me for the cost of shipping, you'll make me a very, very happy man. :)