Challenge Accepted
Sam Anderson challenged himself to build a 733-horsepower classic Mustang
By Steve Turner
Photos courtesy of Sam Anderson
If you have built more than one project car, you always want to push the next one to a higher plane than the last. That was definitely the case for...
Looking for stock used parts from a coyote 5.0:
Coil packs
Injector wiring harness
Timing chains and covers
Valve covers
Water pump
Alternator
Control Pack
Whole front dress if you have it (alternator, water pump, pulleys, idler pulleys, etc.)
Call or text me at 801-232-1292, text preferred
I am doing a direct 2.5l swap in my 2000 Contour svt and before putting the new engine in i am replacing the front and rear main seals, the oil pan gasket, the intake and valve cover gaskets, the clutch, and the serpentine belt, i looking around i cant seem to find the torque specs for the oil...
Hey everyone so i just recently purchased a 03 Cobra Motor for my 91 fox coupe swap, along with the 03 fuel tank. I had a question about the EVAP system. I was reading up on some other threads about people deleting the EVAP system and running into problems with the ECU throwing codes and causing...
Gift Horse
For his wedding anniversary, Lew Mesta scored a modernized ’66 Mustang
By Steve Turner
Photos by Steve Turner and courtesy of Rebel Kustom Paint
If you want the secret to a long-lasting marriage, you might want to consult with Pat and Lew Mesta. The couple celebrated their 50th...
The IRS to my 2001 SVT Cobra is going out. I just ordered a 03/04 IRS from ebay for $1,500 + shipping($300) = $1,800. I also ordered new sway bar end links, sway bar bushings, and a Ford racing irs differential cover. Mine as well get those replaced before installing the IRS. Now once I make all...
Hello all, I recently swapped a 2003 cobra engine and T56 into a 1999 cobra. Now I have a ton of parts and a good 1999 aluminum block 4v cobra engine and 5sp trans. My original plan was to find a gt body and throw the 99' engine in it for a toy. But recently I've had a change of heart. I own a...
This is just a feeler. I may wanna sell my mustang due to needing an AWD vehicle and a useable backseat. It was originally a 2004 competition orange mustang V6. I had it converted to a 4.6 2v t3650 5 speed. Motor came out of a 2000 mustang GT with 49k miles currently has 54k miles on the clock...
ran into a tree the car was totaled the whole car is shifted and can see it in the convertible top, for sure frame damage the engine is completly unharmed car has 140k miles with the polished svt wheels. how much is the car worth with the complete engine intact, it starts right up. the car is...
Looking for T56 with bell, Drive shaft for solid rear and cross member. If the t56 has a 26 spline input will also need clutch setup for 8 bolt crank. I will pay all the shipping to Ontario CANADA.
My engine in my 2001 cobra (116k miles) needs to be rebuilt, instead I bought a engine with less miles. I bought a mach 1 engine with mid lengths and a jlt ram air with 62k miles. I am wondering what Ill need to do to swap this. Is it a direct swap since its a complete engine? I know it fits in...
Hello everyone, new to this forum so I apologize if I posted in the wrong place! I have a 2003 Mustang GT with a Coyote swap. Will be ready to fire within the next couple days. I bought a kit from Jegs that included the motor and controls pack. I have been told by many people that the car will...
i have an 01 cobra with a vortech v2 sc. the belt slips pretty bad on it and have been looking into an 8 rib pulley setup. have done some research and found people saying they use a 5.4l f150 pulleys except for the blower pulley which cuts the price over half. Does anyone have updated part...
So after much google searching with no luck to my specific issue, I turn to you guys. So here is the low down...
Last year swapped a 99 cobra 4V in my 00GT. Swapped motor, engine harness, and ecu into my car. Ever since the swap I have not had a working speedo (all other gauges work fine). Ive...
Hey everyone I'm new on here, iv got a 05 gt I just swapped in a t3650. Swapped in the manual engine harness and Bama send a tune to switch to a manual transmission, it'll start but goes into failsafe mode and throws 15+ codes. Mostly shift solenoid codes and torque converter open circuit...
I have a IRS swapped into my 98, would like to trade for a solid axle with gears and good control arms.
IRS has 4.10 gears, stock springs with 1 coil cut, stock catback with flowmasters welded in. Also newer pads and rotors (less then 3k miles)
Looking for a 99-04 solid axle with gears (3.73...
Hey guys, so 6 months or so ago I bought a 80,000 mile 4V from a wrecked 99 cobra to swap into my 2000 GT. Love the 4V power, it runs great! For the swap I swapped in the motor, ecu, and wire harness from the Cobra into my GT. Turned PATS off through custom email tune. Kept my T45 from my GT and...
Hey everyone I have a quick question. I'm looking at a 2003 gt mustang with a full 03 cobra swap. The motor/body all 03 cobra parts. My worry is if the motor or anything else was stolen. The owner gave me the vin and the number to the mechanic who built the motor. My question is how can I find...
sorry if I posted this in the wrong forum but anyways;
Had a v6 mustang and wanted to do 4.6 dohc swap, wasn't thinking and got all my stuff together and then found out my transmission I was going to use doesn't fit and am tired of spending money on this stupid project so I'm selling it all...
I'm trying to part out my cobra and was curious what I could get out of selling the full swap with my 8.8 rear end. I have a 5.0 rebuilt with 55xxx and rebuilt tranny with 12xxx plus I've got an ecu and harness. Any suggestions on what a fair price would be?
Engine & chassis has 62,000 original miles on it. The eaton swap was done using parts off of a 30k mile 04 cobra that went turbo.
Mods
Stock 99 motor with eaton swap
Tubular K-member, control arms, & coilovers (front)
UPR rear control arms (SRA)
Metco lower pulley kit (stock ring)
Canton...
Read a lot of forums.. found as much info as I can.. but i want to double check this since I'm ordering everything half way across the world and need it to be ready for when i get home. if you've done the swap, please chime in! just want to make sure i've got it all covered.
1995 Mustang GT...
I have a complete Lightning supercharger swap i would like to sell. I had a complete 2000 lightning motor in my mustang until a piston melted :cryying:. I have all the intake components, the elec water pump, 80 mm mass air, stock lower pulley, Belt, heat exchange, stock lower pully and...
I don't know if I've ever seen a write up on how to do this, if so I apologize. It seemed simple enough.
Step 1. Remove your taillights and harnesses. (If, you've got a set of '99/'01 tails I assume you know how to do this part, so I didn't take pics.) In case you don't, you need to...