Did a search but can't seem to find anything that was completed and working .
Trying to decide between a turbo or procharger set up.
Anyways. Can get a deal on some 60mm gen 2 new turbos. I've tried to keep up with the sizing but I get lost
Compressor is 60, turbine 62, A/R .68
Would like...
Been out of the game for a long time, a little back storey. My car is a vert, full suspension, mini tubbed, narrowed 8.8 with 9" ends, was manual brakes and steering.
I pulled it apart to put a proper cage, new high comp engine 88 turbo, TH 400 but then didn't have the heart to cut up the car...
So. Long and short. cars been off the raod for three years do to personal issues in my life. I've finally got her running again but need a set coil packs. I can sense a miss in 1 plus the last time the car was at the track I had a lot of issues running e-85...
So, I can get a set of LQ9 coils...
I have a 10 spline input shaft with about 4000 miles 75$ obo
03 cobra Flywheel with about 4000 Miles, will need to be resurfaced as I murdured a centerforce on it. $obo
Stock 03 cobra clutch and pressure plate with only 3000 miles. Good clutch, held an 11.0 and seems to be much stronger...
39lbs injectors less then 5000k's. 100$ plus shipping 03 cobra clutch less then 5000k's. Best offer, intake plenum best offer. I'd you want to do your own port work I can weld it up cheap then port it your self). Blower bracket that holds the sensors with sensors new but 1 has a crack. Best...
I have the mid plate for a lighting. I bought the full swap but used the intake to make a custom 2v eaton swap. I just gave the manifold
Looking for best offer. I can ship out friday other wise it will have to be shipped from canada
I have a 2.6 pulley and hub, best offer no low balls, came with my M122 blower but ended up going to Cogs.
I can ship from Canada or I can drive accross the boarder and ship from michigan. All depends on how long you want to wait ect But I ll figure out cheapest ect for you..
Thanks Jim
Ok, To start off I live in canada soo, If your in a rush I can send them from here or if you can wait an extra couple days I can send them from Michigan for a lower rate since I m back in forth all the time. I can send it from canada at 0 dollar to avoid the extra cost or possibly send it from...
Came close, did a run to check the tune, no ice running hot and it ran 11.07 then let it cool off and packed it with ice and it blew the clutch.
Hoping to get a new clutch in ASAP and try some dry ice with some cooler weather. Really trying for the 10`s on this stupid thing.
aCiD99GT's...
Got a hold of some vids that someone ealse took.. Wish I gad a go pro lol.
This was pump gas, and street mode other then my cat back off and slicks ported eaton only..
Still want to hit a 10.99 before the years out. I ran a 11.2 @ 124 with a 100MPH 1/8 mile and a 11.3 costing thru 4th...
Went to a grudge day and hit the magic number.
It was warm out and my IAT's were thro the roof but the car laid down a 11.42 @ 122 with a 1.69 60 foot.
The car started pulling timing on the top end, need to figure out what happened to the inter cooling system. I normally don't go over 140...
Sooo, I went to a dyno day with the aluminator and high hopes but the car only put down 466 at the wheels :(.
Conditions in the shop were 89 degrees 30% humidity. First pull made 455, second made 466. IAT2's hit 128 on the second run, car stayed 19-21 degree's timing from 4-6500 air fuel...
Hey, I was wondering if I could get some help. I ve searched and searched and get many diffrent answers.
The Car is a 2002 GT with....
-New aluminator block
-Stock 03 cobra heads and cam's
-mid lengh headers
-Off road H pipe
-Stage 5 blower
-JLT CAI
-TR 7'a Gapped to 29
-94 octain...
I have a stock lower pulley with cage. I went to cogs so I do not need it. Looking for 100 Obo. Will post pics if anyones intrested. I will trade for a I/c pump. Thanks Jim
I need a JLT shipped to me by friday.
If you have one MSG me and I will pay pal you ASAP. If not I will have to buy a new one.
Also need TPS, throttle cable, bracket, Intercooler pump, Idle are control motor and MAF.. thanks Jim
I am looking for the following to finish up my buddy's eaton swap. JLT cai, tps sensor egr tube (I need 2 of the egr tubes), intercooler pump ( also need 2) stock mass air flow sensor. Cobra throttle cable and bracket. Also may be interested in a t 56 if the price is right. Thanks jim
Ok I built a new aluminator and put it in my foush fobra (gt). I have a 03 cobra harness but I'm using my gt computer and dash harness just modding the 2. I've searched and found many answers but still need help with a couple. A) do I need to add another coolant temp sensor to the system? B) I'm...
Gauging interest on a Trade as funds are running low on my swap.
I have a 2.3 whipple.. Blower, snout, pulley.
The whipple has had something small go thru it at some point.. I bought it for 600 to put it on. I have taken it apart at my shop. It needs a quick clean up 2 rear bearings and...
I have a 0 mile brand new eaton, only mounted on my aluminator engine, not even a scratch on the case or rotors for sale 400 OBO cdn plus shipping. Everything is there and a brand new plenum. I am keeping the snout tho..
Stock Lower with cage USED
125 OBO plus shipping...
I have a 0 mile brand new eaton, only mounted on my aluminator engine, not even a scratch on the case or rotors for sale 400 OBO cdn plus shipping. Everything is there and a brand new plenum. I am keeping the snout tho..
Stock Lower with cage USED
125 OBO plus shipping
Brand new...
Hey, just wondering if anyone has modded the cooling system..
I dont have a Termi to start off with so I have to build everything from scratch. To mate the aluminator to the GT.
I m going to be running a remote mount filter and oil cooler. I d like to run both sides of the cross over tube...
I m putting together a Terminator motor using an 03 mach 1 block.
I kept looking for the termi torq specs and relized the main caps are different so I m wondering if anyone has the torq specs?
Thanks Jim
Hello, just getting my new motor together, I went too ford and they couldnt find the specs and I ve looked at a build thred on here and dont seem to find exactly what I m looking for..
I'd like to know, the main cap with sequence and torq specs, Rod caps, and the head bolts sequence and torq...