Search results

Sale pending.

Have had a few people interested, but no money has been put up yet, so the trans is still up for grabs. I plan to start removing it from the car this weekend and will post pictures of the whole trans and components once they are out. Also, I have a trans cooler and custom 3/8" stainless lines...

I've had some people inquire as to why the car has been sitting for as long as it has. To be quite honest, I was going through a divorce 4 years ago, and my ex-wife decided to break out all the windows in the car thinking it would hurt me, and it has been sitting in my driveway since because I...

Still available.

Update: If the buyer wants this shipped, I will ship it via LTL truck freight. I will build a custom crate on a pallet that the trans will be strapped to, and there will be shielding over the input and output shafts to protect them from getting hit by anything. I should be able to get the...

I’m selling a Lentech Strip Terminator 4R70W automatic transmission with a 2600 stall non-lockup stainless steel torque convertor that was custom built by Ultimate Convertor Concepts. This is a 4 speed that can handle up to 1500 hp & 1000 lbs/ft of torque. This setup from Lentech costs over...

Hi There, I saw a couple threads mention that you did a 6r80 swap with one out of an F150. Other than differences in the cases, are the internals mostly the same? I'm putting one behind an 04 Cobra engine with an aftermarket controller so I'm just wanting to make sure the innards are basically...

I have a 2004 Terminator engine for sale that I've had swapped into a 1981 Mustang. I came into possession of the engine back in June, 2005 after it was removed from a 2004 Cobra that had only a couple hundred miles on it. I actually had the California Highway Patrol run the serial number on...

I have a Kenne Bell 2.4L blower set-up for an 03/04 Cobra 4.6. This came off of the Terminator engine that I have in my 81 Mustang. It needs a rebuild as it leaks oil from the front gear area into the blower case pretty badly. I opted to upgrade to a 2.8 LC compressor instead of getting this...

Read this blog. If you want to see PINKS ALL OUT in 2011, you need to send an e-mail to SPEED Network. 2011 PINKS ALL OUT DATES / NHRA UNLEASHED DATES - NHRA Unleashed

I was at ST Motorsports in San Bernardino, Ca on Tuesday and they were doing a VERY SPECIAL install on the owners 2011 5.0. From what I've heard, there are NO 2011's with this upgrade on the street right now. :whisper:

Up for sale is a D&D Viper T56 (This is an actual Viper trans, NOT a Viper-spec, which is just an upgraded T56 with some Viper parts). As far as pricing, I'm going to extend the offer I made to a couple people who are trying to get the money together. I will do $2550 shipped (That's $2400 +...

Okay, here's the last of the Terminator parts that I have left to sell: Twin Terminator fuel pumps ($100 FIRM shipped) - These are the stock purple top fuel pumps that I ran in my car with the 39lb injectors, and they were removed to install some Focus pumps when my set-up had about 5000...

I'm selling a Lentech 9.5" Non-Lockup torque convertor with a 3900 stall. This came with a 4R70W Strip Terminator transmission that I purchased with only 2500 miles on it, and I went with a different 10" torque convertor. This TC also is made for a 35 spline input shaft that would normally...

Okay, here's the last of the Terminator parts that I have left to sell: Twin Terminator fuel pumps ($100 FIRM shipped) - These are the stock purple top fuel pumps that I ran in my car with the 39lb injectors, and they were removed to install some Focus pumps when my set-up had about 5000...

Okay, I'm selling some 03-04Cobra parts that I have. Complete set of 39 lb Terminator injectors ($120 FIRM shipped). These were run for the first 5000 miles that I had the Terminator engine in my 81 Mustang, and were only removed to install the FRPP 60lb injectors. Twin Terminator...

Okay, I'm selling some fuel system parts that I have from my Terminator engine. Siemens 60 lb injectors ($280 obo). These are the Siemens 60lb injectors that do not require the wire harness adapters. They were installed around May of last year, and have about 8000 miles on them. I'm only...

My car is currently down to swap in a Lentech 4R70W Strip Terminator trans, ans at the same time I'm also working on a custom inlet tube for my Kenne Bell supercharger. I realized that I have a throttle body that can flow over 1600 CFM, but the stock Kenne Bell inlet elbow is only rated at...

I'm selling a Lentech 9.5" Non-Lockup torque convertor with a 3900 stall. This came with a 4R70W Strip Terminator transmission that I purchased with only 2500 miles on it, and I'm going with a different torque convertor that's more suited for my daily driven set-up. This one sells new for...

I'm selling a Lentech 9.5" Non-Lockup torque convertor with a 3900 stall. This came with a 4R70W Strip Terminator transmission that I purchased with only 2500 miles on it, and I'm going with a different torque convertor that's more suited for my daily driven set-up. This one sells new for...

Up for sale is a D&D Viper T56, for $2900. It's coming out of my 81 Mustang that has a 2004 Cobra 4.6 in it. You can see the base specs for it at: http://www.ddperformance.com/shop/product_info.php?products_id=170cPath=107_92_126 This trans costs $3500 from D&D for just the trans itself...

I'm looking for someone who wants to trade a complete turbo set-up for a Kenne Bell 2.4 set-up with ALL pullies, brackets, bolts, etc. What I have is: -Kenne Bell 2.4 (w/ 2 pullies for 17 psi that made 543 RWHP on 91 octane and 18.5 psi that made 607 RWHP on 100 octane) -MAC cold air...

Does anyone have a power steering reservoir bracket from an 03/04 Cobra motor? Thanks a bunch.

Okay, for those of you that need the history on this, goto this thread: http://svtperformance.com/forums/showthread.php?t=444669 For everyone else: I GOT IT!!!!!! :banana::pepper::D:rolling::beer::rockon::burnout::coolman::):thumbsup: It may have cost $2500, but I got it. They had the...

I posted a thread for LEO's last week (This thread is open to everyone) about finding out that my beloved 04 engine came up stolen when I asked the CHP to run the numbers for me. The thread is here: http://www.svtperformance.com/forums/showthread.php?t=443425 First off, thanks to FORDSVTfan...