pulley

I have a few things laying around. Everything is OBO to make it all sell. Shipping is included for all but the blower. Will help with that. I should of but did not clean up everything. This is how it came off. Any questions shoot me a PM. Thank you! BLOWER AND PLENUM TOGETHER FOR $525 SHIPPED...

Selling my Billetflow 2.93" clear pulley, Hub, Bolts, and Washers. Will not separate unless all pieces are spoken and paid for. SOLD!

Hey guys I'm finally going to pulley my 03 cobra. My question is since I have to get retuned anyway should I just spend a bit more and find a ported eaton? I have a bap, mafia, and idler pulleys already purchased. Would I need anything else if I went to a ported eaton? Injectors? Let me know...

How do I go through with removing my stock pulley on my Cobra? Do I need to remove the snout? Thanks. -N:coolman:

How do I remove my stock pulley off my Eaton on my Cobra? This may be on here somewhere but I want to install my 2.9 ASAP. Thanks! -N:coolman:

Changing directions: selling my ported Eaton and mods as a package. Zero miles since porting. Ported Eaton - cleaned/greased needle bearings, new GM SC oil, inspected coupler Welded & Ported, matched oem plenum Ported oem TB BF black 2.76 pulley LFP 90mm pulley with bracket (new) MAFia F7373...

Just lookIng to see what everyone else's take is on Lunds canned tunes for a pulley, intake, OR/X, 170 thermo and heat exchanger car with tr6 plugs. Any one with a set up close to this have any opinions on there impressions? Hopefully as non biased as possible lol.* Also any ideas why the...

Just lookIng to see what everyone else's take is on Lunds canned tunes for a pulley, intake, OR/X, 170 thermo and heat exchanger car with tr6 plugs. Any one with a set up close to this have any opinions on there impressions? Hopefully as non biased as possible lol. Also any ideas why the...

Have some parts i no longer need so I'm looking to sell. Not sure how to upload pictures from my lap top so text me or email me and i can send from phone. All parts are located in Miami, Fl and will ship at buyers expense as well as paypal. 03/04 cobra front UPR coil over sleeves w/springs...

Pulley has a 1/8" dent in the top, outside edge. I have not tested it to see if there will be belt wear or slippage. $25 shipped Craig 901-493-1099 for text messages

looking to buy a 3.5 pulley for a 2.9 whipple.. if anyone has let me know asap text me 516-343-4977:banana:

i have an 01 cobra with a vortech v2 sc. the belt slips pretty bad on it and have been looking into an 8 rib pulley setup. have done some research and found people saying they use a 5.4l f150 pulleys except for the blower pulley which cuts the price over half. Does anyone have updated part...

I just got done putting cams in may car and just put the crank pulley on now its hard to turn and metal shavings from the timing cover are coming off and a ticking sound. the engine turned fine before i istalled the pulley. The ticking sound sounds like its coming from the crank pully i don't...

SOLD!!! Bought this a few months back and never used. Ended up going with a different setup. Includes entire Metco lower hub kit, bolts, etc. and 4# lower pulley along with proper 3.20" alternator pulley for use with the 4# lower. Everything brand new in the box. $400 shipped for both...

$100 shipped. SOLD SVT Attachment program isn't currently allowing the uploading of pictures. I'll try again to post later today. PM, respond below or text me at 901-493-1099 Thanks, Craig

Hello. Ive been lurking for a while and figured I would finally register and ask some questions about my car. I have an 08 Shelby and I am in the process of doing some upgrades this winter. I currently have an 08 GT500 with HPtuners and have tuned for my JLT 123mm CAI. I have these parts...

Looking for a 3.5" pulley for my 4.0 Whipple. Text me at 702-466-4007 Thanks guys

Hey guys, I need to replace the teflon o-oring on my high/feed pressure line. Its the end that goes into the power steering pump. I have to get at the nut that's right behind the power steering pulley. I remember that when the motor was out of the car I was not able to get to it properly...

New in the box Steeda pulley removal tool. The packing list shows it to be for 2007-11 GT500's, part # 555 8902. $100 shipped, 979-709-2508

Hey guys I picked up this brand new innovators west 10% lower pulley off of lethal performance to complement my 2.3 tvs swap... However I found a good deal on a used 4.0 whipple and decided to go that route... My motor is stock and I am not planing on upgrading internals any time soon so the...

Sorry if this is already up somewhere. I saw plenty about each topic individually, but nothing comparing the two. SO, lets assume a guy has just bought a stock 2011 GT500 as a DD in Houston, and he has about $800 for the first mod. Pulley and tune...

Have off an 03 Cobra Stock Pulley Stock Belt Stock pulley cover Dual gauge pod (speedhut) Rear Stock Mach 460 speakers & amps Make an offer on anything and I will ship! Message or text 919-749-9299

Used Metco 6LB Pulley Setup SOLD! VegasBaby (from Lightningrodder) Oil Separator SOLD! JLT Budget CAI, brand new, $100 SHIPPED

HEY GUYS JUST GOT BACK FROM OVERSEAS AND HAVE A BUNCH OF COBRA PARTS ALL PRICES ARE FIRM AND FAIR REASON THAT IM SELLING THESE PARTS IS BECAUSE I BOUGHT A VIPER AND NEED FUNDS FOR GOODIES I ALSO HAVE A BUNCHOF LIGHTNING GEN 2 LIKE OEM LIGHTS BILLET GRILLS CAN SHIP SAMEDAY I GET PAYMENT I AM ON...

looking to buy a diablo tuner for 03-04 cobra but must be a pre-2009 tuner with the out of the box tunes intact and unlocked. not interested in blank ones bought at a shop with only custom tunes installed. also looking for RR reichard racing 2.65 pulley for an eaton.. let me know what you guys have.