pulley

prefer Reichard Racing but not picky. PayPal ready. Thanks.

Hey guys have a brand new whipple 2.9 with 3.5 upper pulley. I have only mounted on lower manifold hasn't been installed on car or even put oil in. Should still have warranty as ive had less than a year. also selling brand new id1000 injectors Whipple 3700 shipped id 1000 850 shipped...

**** SOLD **** Hello SVTP, I am listing my 13 GT500 for sale. First off, I am asking $47k for the car. I do have a lien on it at a local credit union. Currently at 22k miles and will go up as I drive it on nice days. Always has had Amsoil Signature Series 5w-50 oil. ***TRADES*** I will...

I’m posting this for my Dad, we recently picked up a Top Sportsman car and would like to free up some funds to start running that car regularly. This car is in great condition, garage kept – and under a cover most of the time in the garage. About the car: 2011 Shelby GT 500 (8900 miles) One...

Hi all, I have a 2010 GT500 with the stock M122 and was looking for your opinions on what I can expect as far as RWHP from these following mods. The car currently has a 2.6 pulley with a dyno tune for the pulley but I am looking to add a JLT Big Air CAI, Twin 65MM throttle body, VMP inlet...

13-6 kit barely used less than 1000 miles. I am looking to sell the car so I removed the kit. You will likely need to send the SCT tuner out or get with Revan Racing because they needed my PCM calibration and that might need to be adjusted. Currently set up for 91 octane but could most likely...

Found one......

I am selling an Accufab throttle body in good condition and an UNUSED Whipple 2.75 pulley. The throttle body comes with a gasket and the pulley comes with the bolt kit. Both were part of a project that I changed directions on, so I never used either part. Accufab Throttle Body - $270 shipped...

I have a Metco Pulley Puller and a Metco 2.70 Pulley/Hub kit. Both are still in the box and have never been used. Metco Pulley Puller - $95 Shipped Metco 2.70 Pulley/Hub - $90 Shipped *Prices are either before PayPal fees or PayPal sent as gift (no fee)

i purchased a 01 cobra that came with steeda's undrive pulleys, ive seen a post on here that said a oil pump blew up because of these on a 4v. Can these really do that just from undriving the accessories? If so would it be safe to say they need to be taken off?

I bought the billetFlow Supercharger pulley to change out pulleys with ease. I also have the Freedom Racing 3V Valve Spring Compressor tool and Timing Chain Wedge set for rental. I figured I'd rent them out for anybody that needs them. -Price: $25 plus you cover shipping fees (13.50 priority...

I bought this about a month ago. Used it. Works great. Nothing wrong with it. But I don't need it anymore. You may as well buy it used, save a few dollars and then resell it once you are done. $110 shipped.

Looking for a 6 bolt VMP Cobra TVS style pulley, would prefer something close to a 2.6" but I'm open to anything available. Just need a pulley to get belt alignment figured out for a custom mounting plate for my project. Thanks!

I have a take off tvs that I bought off of here from another member. It is powder coated white with the 5.8 shaved off and the svt painted red using torch red touch up paint, was blue when I bought it and painted over it. It has a 2.4 pulley installed currently and has a chip in the power coat...

I bought this from a member on SVTP, and never used it. I have since decided to go with a Whipple 2.3, and need to sell for money to fund the swap. Inlet was not ported by Posi, but it is a pretty good match and looks like a quality port. More than willing to ship to the lower 48 states for...

Title says it, looking to grab a Reichard Racing pulley for a Whipple. Looking for sizes anywhere from 2.6" - 2.9". Preferably a 2.7 or 2.8. Also, if anybody has a Dayco PolyCog style belt around a 76", let me know. Thanks!

Hi guys, im looking into buying a P1SC procharger that came of a 98 GT and im trying to put it onto my 2002 Gt. i know the mounting bracket and belt are different but is that all?

I am not using so selling my Metco 3.20" alternator pulley. Only mounted for a couple of minutes then had to change to a different alternator. SOLD!

So I'm hoping that you guys might be able to help. I have a Race Posi Port Eaton with a 2.73 upper and 4# lower. I believe that the previous owner changed the alternator at one point and it looks as if the pulley is just the one that came on it from whichever parts store it was bought from. I'm...

looking to buy a 2.75 inch whipple pulley for my 2.9 whipple on my 03 cobra. Only in good shape please! Thank You!

Wanting to buy either a 3.2" or 3.5" Alternator Pulley. I have a 4# Lower and reading some forums people has had good luck with both. I had a 8 rig that is now damaged but I would really like to find me a 10 rib. Also looking for either a 3" or 3.25" for a 3.4 Whipple. Thanks in advance.

I have a Diablo sport predator tuner. Works great. Used to change my fan settings and other things. switched to sct so don't need this. Has pulley tune in tuner for the pulley that comes with it along with the other tunes. Pulley is a 2.8 diameter press on for the eaton m112. That is about it...

4.6 mustang mishimoto aluminum radiator-sold Ford Racing Fr500 Cam in great shape- $575 obo 03/04 cobra parts New 03/04 cobra strut tower brace for eaton supercharger made by steeda- $50 03/04 cobra cold air intake filter and heat shield- $40 Metco lower with...

Hello, I have recently parted out my cobra and have no use for these items l. All items have 300-350 miles on them 2003/2004 Cobra 1-3/4 ARH Long tube headers with 3in to 2.5 inch x-pipe. No dents or issues whatsoever. Paid 1400 new, 900 Shipped FIRM Sold OBO + shipping Reichard Racing...

10-15k miles on these. In like-new condition, never had any issues with them. Crank, water pump, and alternator pulleys...$100 plus shipping, obo.