Recent content by Riskeman

Location: Westminster, MD Will add photos soon. - Craigs list link - http://baltimore.craigslist.org/cto/3936806957.html 1996 Mustang Cobra. 127k. Milage will rise as I am daily driving this car until it sells. price drop to $8,000. This is a high horsepower, well sorted out car...

Looking to buy 94-98 mustang axle shafts. Can be either from 8.8 or 7.5

I recently bought a fox rear with an Auburn diff in it. I pulled that axles and while draining the oil I found 4 of these. My question is what are they. Do they belong to the Auburn diff? I can't find anything about them in Auburn's exploded views or manuals. The previous owner had the...

I finally have finished the install on my pieced together vortech kit. I'd like to start it up and let it idle to burb the cooling system, look for leaks, etc.. However as it sits the car won't startup and run. A little background info: 96 cobra, v2 sqi headunit, 3.6 pulley, I did and...

I'm about to install my pieced together vortech kit and I'm actually worried about making too much power for the 130k mile stock block on my 96 cobra. v-1 Si trim (1150 cfm) 3.6" pulley afm power pipe water\meth injection lmaf 90mm 42lb injectors walboro 255 highflow catted h pipe...

I just bought a V-1 S trim off of ebay and surprise, surprise the impellar is messed up. It looks like a few of the blades are bent and one is cracked. What are my options? I don't know anything about blowers so something else might also be wrong with it. Should I just send it to Vortech...

I'm looking to buy a Vortech V1 S-trim or V2 -SQ trim CCW headunit for a blower kit that I'm putting together. Cash in hand and ready to buy! Let me know what you have. PM or [email protected]

Anybody have a vortech head unit forsale? I'm looking for S or SQ trim CCW rotation.

I'm piecing together a vortech kit to put on my 96 cobra. stock original engine 120,000 miles bbk h pipe with welded in high flow magnaflow cats magnaflow cat back imrc delete plan on running a v2 s trim kit with vortech intake piping 42lb injectors, lmaf, 255 walbro meth/water...

I'll try to keep this short. I took my car to a mechanic that does work on the side at his house to get gears done three weeks ago. He hurt himself while working on my car, but is now back at work. The problem is my car is still sitting in his garage with the rearend out of it while he is...

I've started having a cooling problem while cruising at highway speeds lately. When I'm in 5th and driving around 70 mph my temp will gradually increase from its normal running temps to hot. If I drop it into 4th to increase the RPM the the temp will drop back to its normal temp within 30...

I recently bought a 96 cobra with 115K. It runs decently but I don't have a good comparison to be able to tell if it is running the way it should. I pulled the codes and came up with... p1443- small or no purge flow condition p0411- secondary air injection system incorrect flow p0420- cats...

While doing a clutch job I noticed this brace on the chasis is bent up and is actually hitting my bell housing. Here is the best picture off the web I could find... I need a new one or to some how try to staighten this one but if I bend on it I'm sure it will be hard to get it back...

I've searched, but still need some help... 96 Cobra. I'm trying to install an Autometer mechanical water temp gage. First I tried to install it where the factory gage sending unit goes, but none of the included adapters will work. Is there a better place to install the probe, or do I...

Hello everyone, I just purchased a 96 laser red Cobra and will be on here frequently looking for advice and knowledge. I can tell there is a lot of info on here! Ron