The car is a novi 2200sl with full supporting mods, wastegate, 50mm bov, 3.33", just under 10psi max boost... Ect ect. M6 3.31 gear, rear tires are 305 555r's, 27.6" tall...
Ok the car is insane! It feels like a monster compared to when I ran a 11.1 @ 130.5mph... First and second just light up...
So I said screw it, I want deeper 10's! My pb is a 11.1 @ 130 on a street tune and nitto dr. I decided to compliment my 100 octane race tune I would get some better wheels/tires. I went with the race stars 17x4.5 and 15x8 for the rear. Choose M/T slicks 28" x 9" should be nice and light and dead...
So guys some might know I took my car to the track last weekend for a few shakedown runs. Since my last runs for power anyway the only thing I added was a waste gate, 100" HD gates belt, and the 3.33" pulley. Plus I cleaned up my charge pipes by porting all the cold side piping. Also added a...
I want a set of race stars, was thinking AM because they come ready to rock. Pricing is decent with the forum discount ect. But I have 2 issues. They only sell a 26" tall front runner bias ply, I need 28". Also the front race stars are out of stock.. Ideas?
Car has some bolt ons, 100% stock motor. Stock headers ect.. 3.31 gear + 27.6" rear tire. Lots left on table, tune is set to 15* max timing, 11.1 wot a/f, tuned on 93 but running straight 100. Went sideways in 1st, they are my full weight street setup. 275 wide fronts, 305 555r in the rear...
Car has some bolt ons, 100% stock motor. Stock headers ect.. 3.31 gear + 28.5" rear tire. Lots left on table, tune is set to 15* max timing crazy rich, tuned on 93 but running straight 100. Went sideways in 1st, they are my full weight street setup. Stock suspension. Stock mt-82 doing work!;-)...
If it's slipping with a 100" belt what are some ways to fight it? I was thinking maybe there might be oil on it what if I sprayed it down with some simple green? Should that help it stick without ruining the or make it squeal?
Any ideas would be helpful!
Did my gear oil and tranny oil to royal purple this weekend and noticed my axle breather was leaking. Did the research and I'm going to build my own catch can since it'll cost way less then anything I've seen offered. They ranged from $120-200.
Any members interested I'll build extras. Has...
Getting ready to bolt this in. Charge pipes are ported, opened up 1/8" +. Just waiting on welding.. I have the chart that shows springs for 8.7 psi then 10.15psi (red/black) I want to run about 10psi max..
Also what size fitting are you using to tap the charge pipe for the wastegate vacuum...
Looking to see how I stack up. 2011 5.0 stock engine, a little blower, crappy mt-82, crappy 555r's, heavy fully loaded glass roof car..
Looking for stock engine but blower swapped cars. :) or even stock blower cars. Just no built race cars lol
So I got my wastegate and right away noticed the weight of the flange..turns out it's stainless steel. I'm getting this welded next week and last time I checked you can't weld steel to aluminum...or can you?! I need to know so I can order the correct flange first thing in the morning
Lastly...
I've sourced the bov + gate for $628 shipped and I'm getting a 3.33" pulley aswell. I plan to run the black/red spring which is 10.15psi max. Also I've found 5 pumps around me that sell 100 octane unleaded. I'll be running that full time since this is not a dd.. What can I expect over my stock...
http://www.amazon.com/gp/aw/d/B00AG5CTP8?cache=12fe4c779e33fe15db8cabb5db52fe2a&pi=AC_SX110_SY165_QL70&qid=1401492536&sr=8-38#ref=mp_s_a_1_38
So can anyone chime in that's bought this? Each fan has a blue and black wire, power and ground. I wired both the blue wires together and same with...