rebuild

Hello everyone! I'm here for a smidge of advice, where ever I can find it. I have a Gen 1 coyote which I just recently pulled out (mainly for TKX swap). I mostly focused on heads and timing. It got new lifters, MMR springs/retainers, billitt oil pump/crank sprocket, pickup tube, windage tray...

2003 cobra coupe 65000 miles. Had the engine rebuilt in fall of 2020 (it had a leaking intercooler and no compression on cylinder 8). I was not given a full parts list but what I was told (that I remember) was replaced: every seal and gasket inside the engine, pistons, intercooler, plugs, wires...

First of all, if this isnt the right place for this, I apologize. Hi all. :) I have a T45 rebuild kit that I bought from LMR awhile back for my 98 Cobra, but I went a different route after the tranny was taken apart. It's all still brand new and in the original packing/box. Bought brand new for...

Getting ready to yank the motor on my Cobra to rebuild its knocking bottom end. Depending on the cost of the rebuild, there's a pretty good chance I'm dropping a set of cams in. Right now my combination is stock B heads, a short runner intake with a raised floor, Ford racing shorties, IMRC...

The bearings in the front of the Eaton are starting to go bad. They are making quite a bit of noise. So the car has been parked for a few weeks now. Needless to say its killing me. :( I am 99% sure I can rebuild the snout myself. I have the kit that I bought from ZZ Performance. The belt...

Hello, I have a 1996 Cobra with 17k miles. It seems as though the 2nd gear synchro has gone bad because it grinds at high revs with quick shifts (Not power shifting or even partial throttle). It has a B&M short throw shifter (Not sure if this could be part of the problem). Is it worth getting...

I have a ported Eaton that sounds like it needs a rebuild. After rebuilding it, will there be a reason to retune it, or can I just reinstall the blower and run it? (possibly thinking of having Stiegemeier rebuild it)

Losing compression on one cylinder. Truck has 115k miles. What all should i do during the rebuild? A friend is asking me to do the work, just want info on what all i should make sure he gets done....

Hey all, So I have a 99 gt with a Windsor motor. I've searched everywhere for a rebuild kit to refresh the bottom end. Only rebuild kits I've seen are for romeo engines. Can't seem to find a full kit for a Windsor motor on A&m, Lmr, jegs, Summit, or rock auto. Any one got anything info for me...

Hey everybody, I picked up a cheap 1990 5.0, with about 97k miles. Needs a little love but overall runs OK right now. But it looks like I'm having oil pressure issues. When at a warm idle, the pressure drops to zero on the STOCK gauge and goes back up while driving. I already ordered a...

Alrighty, so I bought a 09KR from a Ford dealership, with a powertrain warranty, and I immediately experienced rear end whine (car has 45k miles). I took it in to have it repaired a few weeks later as I was busy with the military and paid a $220 deductible to have it fixed. I drove it off the...

I wanna get my 01 cobra motor rebuilt and prepped to supercharge how much am I looking at? Also I want it bored to renew the piston seals how much should I have it bored?

I have an 03 Cobra with a blown engine. While overseas my car was sitting for approximately 7 months twice during 2 deployments. I was told that I should have replaced all of the fluids and got it checked out before putting it back on the road. Needless to say that didn't happen. After breaking...

Like the title says, I'll be building up my every other weekend driven 03 and slapping the 4.0l Whipple on top. I've sent the heads off to be ported and polished, +1mm on intake valves and +2mm on exhaust. Oliver rods and Diamond pistons will be used and reusing the factory crank. Custom ground...

Hey guys, I'm a fairly new Cobra owner. I bought a 99 Cobra a few days ago that had what I assumed was a timing chain tensioner bad, as it was lightly knocking. I got a very good deal on the car, but when I was backing it off the trailer it jumped time and I shut it down right away. Hoping I...

Hey all, i was just wondering if anyone on the forum rebuilds cobra differentials if the entire diff is sent to them, or knows of a good place in the CENTEX area that does it well and correctly with the proper tools. I think i would rather do full rebuild and have the warm fuzzy about it then...

So i'm completely ready to drop my wap 4.6 4v from an 04 mach 1 into my 2000... i'm going w/ a vortech v2 T-trim supercharger pushing it around 16psi w/ an fmic... So to do that i'm gonna forge everything and rebuild. i've never rebuilt a mod motor, but my buddies are professional mechanics, i...

5 Spun rod bearings, Only one was making noise... the others were about to though. Crank is getting turned as we speak, didn't look bad, block looks great, gonna stay with standard bore. A friend of mine that has been building big power race engines for 49 years is letting me rebuild it with him...

I was racing a new Camaro SS, annnd 6900 rpm's later I have a knock going on underneath my drivers side valve cover now. I dont know what it is just yet, idles fine, drives fine, just knocks..... I have never rebuilt a cobra motor and the pony is about to go into the barn for the winter, so I...

I have a 96 Cobra I just bought and the bottom end is still together but the heads are off the motor. Car was getting hot I was told. I am not sure if they burped the motor when they refilled the radiator as the person who owned the car does not know much at all about motors. I am going to have...