Finally finished my 04 Mach 1 project, got it dyno tuned and numbers were 555hp and 474 ftlbs. Does the torque seem low? What could be causing it? On everyone else’s builds, hp and torque are relatively close. Just a curiosity post as the car pulls just fine for what I use it for.
13# boost...
Ok, so I've owned my base 2014 GT 6 speed, which I affectionally call the DudeStang, for almost 7 years. I recently had something fixed that was driving me crazy - some paint damage/scratches on the trunk lid and spoiler. The car isn't in perfect shape but it's in pretty good shape. It could...
Hey all,
I picked up this 99 cobra (Crystal white vert w/ 70,000 miles. Very shiny.) a couple years ago and have been working on getting her into great shape ever since.
When I was buying car originally, I came on here and various other forums and it seemed like the consensus was that all the...
hey guys I am having an engine built at the machine shop using the stock Kellog crank, Stock Manley rods, I need to order pistons suggestions on make and what compression?
2.8 kenne bell mammoth lc
3.5" Blower Pulley
Lower pulley Metco 4#
ARP Head studs
Still has t56 manual transmission...
Hi all,
I am looking for you opinions on aftermarket Coil on Plugs. From what I have read, everyone seems to split on the aftermarket vs. factory COPs in this particular case. I understand that the stock COPs can support 800+ horsepower, and that they'll do it just fine, but does that...
Have an F-150 3.5L EcoBoost? Want more power?
The Borla® Turbo Upgrade Kit for the 2011-2016 F-150 3.5L EcoBoost Trucks transforms the power delivery of the EcoBoost engine. With up to 160HP* gain depending on the year of the truck, this kit really brings the excitement factor you have been...
Stock Block Shock
Anthony Santora built a shockingly powerful S550 with ProCharger boost
By Steve Turner
Photos by Jake Peters Photography and courtesy of Anthony Santora
We know that Ford engineers are focused on creating cars that hit a performance target, handle well, remain quiet and...
Boss Boost
Jamie Linkenholker turned to JPC Racing for a turbocharged RoadRunner
By Steve Turner
Photos courtesy of JPC Racing
Lately we’ve seen lot’s of feedback from people that believe it’s a little nutty to modify a road course-oriented Mustang like the new Shelby GT350. However, one...
This is my current daily driver for time being
Current mods
fender well cold air
steed short shifter
magna flow off road x-pipe
flowmaster cat-back
I would like to say that from those mods I would be close to about 450 rwhp but IT'S NOT ENOUGH!!!
I am going to order a supercharger pulley...
I have searched on other forums and stuff but can never find a good/consistent answer.
As far as I knew, the stock hydraulic lifters couldn't really go over 6000 rpm without floating the valves. But I want to try a different roller cam and rev to 68 to 7000 (engine is prepared for it so I know...
This passed weekend I just picked up an 04 Torch Red Coupe with just under 20k miles on it. Absolutely love everything about the car. The car has a CAI, 2.8 pulley, steeda snub idler, steeda catback exhaust, UPR O/R X pipe, SCT Tuner w/ Bama Performance Tune, as well as a handful of suspension...
OK, how much power is in a point of timing.
How much power do you gain going from 18 degrees of timing to 24 degrees of timing ?
Now lets assume you have the octane/fuel to support the added timing, you have a TVS with a 2.4 and 10% lower and supporting mods.
How much gain can be expected.
we all know they come 320 from the factory but with drivetrain loss in the 270-280 range i dont find that too fitting knowing my cobra is under 300 if dyno'd i do like too have fun with my car of course and maybe a few runs here and there, i want my cobra to basically have the real rating my car...
https://www.youtube.com/watch?v=OSMcHg_7eo4
Flowmaster's ceramic substrate catalytic converters are intended for severe duty/high temperature applications and are engineered to meet or exceed both OEM and USEPA standards for performance and longevity. Protected by a 25,000 mile...
What are the motor mods and suspension mods needed to supercharge my 2013 5.0 mustang? Kit I am looking at is a 2.8l kenne bell. I'm looking to get about 700-800 horsepower out of the build.1000 horsepower maybe later on down the road.
i would just walk outside and look but thats not exactly possible atm.
whats is the 2000 lightnings stock exhaust? 2 1/2 in.? or more.
i was wanting to install some electric exhaust cutouts because CA does not really give me a lot of room to upgrade my exhaust
anyone know a place to...