Recent content by 04silversnake

I took the tranny out to replace the throwout bearing and discovered a loose part laying in the bottom of the bellhousing by the 3 vent holes. It looks like a cylinder almost a 1/2" in height and also in diameter. I had this car since brand new and the tranny has never been worked on. This...

Hello everyone. I need some help. I noticed the passenger side foglight was not working. At first, I thought it was a burnt bulb. I tested and the positive 12V had power, but the negative turn out to be without power. I followed the cable under the wheel well lining and it was burnt and other...

I would like to know if anyone has a diagram or a link of how to use a distributor from a 94-95 in my fox mustang. I like to do this for 2 reasons. First, I already have a new MSD unit for a 94-95 mustang. Second, I think it would be more reliable to relocate the TFI away from the heat it is...

I just installed new replacement brembo rotors and new hawks pads for the front. I ran into the following problem: I pushed both piston all the way in using a c clamp and the old pad, but one side was really difficult to turn the rotor or the wheel. I tried with the old disk and it turns fine. I...

I feel so mad; I took it to the dealer for the rear bearing. I had noticed it when I was installing the Billetflow brace that my rear wheel was loose. It turns out a bad bearing. I brought it on Monday and yesterday I picked it up. As usual, when they brought it back to me, I do my circle...

I am taking the car to the dealer for a bad rear wheel bearing. I have a question, do you guys think I should remove the MGW shifter? can they void my waranty even though they are not doing any drivetrain work? My other mods are JLT CAI, and Borla cat back. Not worried about these two.

FMS-M-6675-C302 This is the part number for the stock replacement chrome oil pan from ford racing. I just purchased it from Summit Racing. I have a few questins. On the pick up tube that it includes, it has a kink pretty noticeable that i believe should not be there, it will be blocking or...

Hello all, this is in my '91 gt. I replaced the stock pump since the original seized and twisted and broke the pump shaft. I got a new one with the standard flow from either Summit or Jegs, cant recall which of the 2, with an ARP hardened shaft. I was driving the car hard and all of the sudden I...

I took the car to the dealer to have a few things done. Still under warranty. First of all, not very good luck with the rep. Was not being very helpfull. Well, I mentioned the following: 1. The car is hard to get in gear, specially reverse. I mentioned to him about the TSB 04-13-4. I did a lot...

This is in the 91 gt. Probably someone can help me. When the car is running the voltage is close to the middle and the engine temperature is about 1/4 closed to the cool position at the cluster. Once I turn on the lights, A/C fan specially in hi, or any other accessories, I notice that the...

I have a 91 gt that came with sunnroof. I removed the tint since it was fading and had a few air bubles. I want to know what you guys do to avoid the hot sun from hitting on top you your head or keep the sunlight from entering inside the car. I am planning on putting the darkest tint, maybe...

I know this is not a Cobra, but maybe you can help. Its a '91 gt I washed the engine and it fire up just fine. I always remove the rotor cap to make sure it is dry, otherwise water always get in there and it start to misfire. Engine fired up ok, and let the car idleling for a few minutes, all...

I know this is not the forum for the fox, but maybe someone can help since this section seem to be the most visited. I am looking for an interior carpet for my 91 fox. Does anyone has any sugestion where to get it? Can you tell me if it already comes with the holes for the seat bolts, seatbelts...

I am looking for an interior carpet for my 91 fox. Does anyone has any sugestion where to get it? Can you tell me if it already comes with the holes for the seat bolts, seatbelts and lumbar air pump wire in it?

Hello all, I just intalled the tune I received from James today to go with my 2.93" BF. First let me say I had the car sitting in the garage for two weeks with 1/4 of gas of tank. When I took it for a test, I noticed it was pinging between 1500 to 2500 rpm. This happened on a little boost, 5-8...