Dasaliac03's Kenne Bell 2v Build Thread......pic heavy!
- Thread starter Dasaliac03
- Start date
TwoVee FTW!
Hell yea nice build should be good for 600
No sir. Sonic blue
going to match my truck and my bike Fo sho!
That's what I'm shooting for at minimum on pump 93
My wallet sure don't! Ha got to pay play, it better be fun!
You should be close to 600whp on 16psi. I had stage 3 pi heads with old school Shawn Jula d cams and made 570/510 on 14psi in 98 degree Texas heat with the 2.2
My car trapped a best of 133 with that setup and ran really hard, I wish the 2.6 sounded like the 2.2 but you will really enjoy the power
My car trapped a best of 133 with that setup and ran really hard, I wish the 2.6 sounded like the 2.2 but you will really enjoy the power
Nice, I'm doing a similar conversion on body panels, just waiting for a tune on the ysi and its going to paint.
Id bet you'd pick up more HP with proper blower cams vs the new blower. I had a vortech s trim mongoose kit from MPH, did all kinds of pulley swaps, power pipe, intercooler and even t-trim swap and nothing woke the 2v up like Tim's blower cams, wish I had made that my second mod after the blower. I picked up about 80rwhp, it made 487 rwhp at 9 psi on 91 octane on a stock longblock other than the cams.
Id pulley that 2.6 to its Max and get a larger crank pulley if you want to get near 600. That compression with stock cams is going to be tough to crack that number. I think without cams and 5-6 more pounds of boost out of a bigger blower you're looking at low 500's. Luckily cams are cheap because we only have two
Id bet you'd pick up more HP with proper blower cams vs the new blower. I had a vortech s trim mongoose kit from MPH, did all kinds of pulley swaps, power pipe, intercooler and even t-trim swap and nothing woke the 2v up like Tim's blower cams, wish I had made that my second mod after the blower. I picked up about 80rwhp, it made 487 rwhp at 9 psi on 91 octane on a stock longblock other than the cams.
Id pulley that 2.6 to its Max and get a larger crank pulley if you want to get near 600. That compression with stock cams is going to be tough to crack that number. I think without cams and 5-6 more pounds of boost out of a bigger blower you're looking at low 500's. Luckily cams are cheap because we only have two
Nice, I'm doing a similar conversion on body panels, just waiting for a tune on the ysi and its going to paint.
Id bet you'd pick up more HP with proper blower cams vs the new blower. I had a vortech s trim mongoose kit from MPH, did all kinds of pulley swaps, power pipe, intercooler and even t-trim swap and nothing woke the 2v up like Tim's blower cams, wish I had made that my second mod after the blower. I picked up about 80rwhp, it made 487 rwhp at 9 psi on 91 octane on a stock longblock other than the cams.
Id pulley that 2.6 to its Max and get a larger crank pulley if you want to get near 600. That compression with stock cams is going to be tough to crack that number. I think without cams and 5-6 more pounds of boost out of a bigger blower you're looking at low 500's. Luckily cams are cheap because we only have two
one of my good friends here locally has also built his 2v and our setups are very similar. He's making ~660rwhp on 18psi with the same blower but yea he does have blower cams..........after trans im sure that will be next for me
test fitting the trunk and spoiler
Dropped the car off for paint about a week ago now
pics from tuesday when i dropped off the side skirts, fog lights, and bezels
Sweet. Car should be a lot of fun when its done.
Filled & shaved the holes from the fender badges, wasnt sure if i was going to run any more so i went ahead and prepped as if i wasnt going to
Hood ready for paint!
Yessir. Wasnt the origional plan. Dropped it off at the body shop with all of the new parts and really got to looking at the car under their lights..........no way it was going to match worth a crap. If i was going to spend the money to paint the whole car, it wasnt going to be back that ugly laser red!
Last edited:
Nice project, keep us posted when she comes out of the booth.
will do!
Users who are viewing this thread
