What would you guys recommend here? I'm hoping this scratch will buff out.
It doesn't really look all that bad.
The scratch is on the rear bumper of my 2010 MKS...Ecoboost of course. :)
Does anyone have a stock halfshaft they'd like to get rid of (preferably
cheap :D )?
I need the passenger side. I'm not sure if the driver's side and passenger
side are interchangeable.
I'll tell you why...
I've had a set of Doug's black pullies, idlers, and bracket for over three
years now. They have seen major abuse, Michigan winters, severe belt
dust, etc so they were beat up nicely...at no fault of Dougs. These
were the soft anodized version. They're now hard anodized...
Who's got the black Cobra with HRE 545's? It's an IRS car with
exhaust. Not sure of any other mods, but it sounded pretty healthy.
I keep seeing it in my neck of the woods (Telegraph & Cherry Hill).
I currently have the stock '03 seats with the Kenny Brown seat rail
extenders on the driver's side. I'm 6'7 so I needed more leg room
than the stock position could offer. I've had them for 3 years now
and everything is fine, but comfortability and seat position (height)
could be...
Just as the title says...
$350 shipped for the following throttle body from Doug
at Billetflow. I purchased this TB from a member here
(Postban) and have decided not to install it based
on the color scheme that I'm going within for my
engine bay.
Here is the TB installed on...
I found it interesting that I was the only '03 Cobra at Milan today.
Everyone else must have them garaged for the winter. I'm a few
days away from that since I finally got a winter beater...'06 Dodge
Dakota 4x4. :-D
I believe I've reached the law of diminishing returns. I've done all the...
I really had no idea what to expect from my new solid axle setup.
I'm still running 315 Nittos which are horribly over-powered.
Anyway...
Lined up and dropped the hammer at 4K rpm. Roasted the tires
to the tune of a 2.2 60'. Too aggressive...should've slipped it.
Peddled 1st a few...
I did a little research and didn't come up with a whole lot for a rear brake install. So here's a few tips for those of you who do this in the future...
Tip #1:
Prior to removing the bottom 15mm caliper bracket bolt, remove the emergency brake cable. Use a good size screw driver or pry bar...
I didn't find much searching so...
How much boost are you guys seeing running a 2.2L KB and a 2.76 pulley? Race or pump gas? How much timing? Power output with this setup?
I'm running a 2.93 on 93 octane currently. Timing is around 18*.
These wheels have been to hell and back. My car is a true daily driver and it's seen two nasty Michigan winters packed full of road salt. The final product isn't as good as a new wheel, but it sure does look revived.
I only did one wheel so far...
Definitely follow Stang2WRX's instructions...
Anyone looking for a Steggy ported blower? I have roughly 6,000 miles on the it. It's a faily recent port job (oval). I haven't really decided on a price yet...something fair is fine. Anything to cut into the expense of the KB. :D
Anyone lower their car and it still be too high? I'm running the stock isolators in the rear and I think I'm going to remove them to drop it a little more. I guess I'll run some heater hose around a coil to prevent metal on metal contact. I'm curious how much of a drop it'll add out back by...
My Cobra is a daily driver and my Bassani tips have taken a beating over the winter. What is the best product and method to bring them back to life?
Thanks. :beer:
Here's the story...
I took a friend for a spirited ride since he'd never been in an '03 Cobra. I beat on it pretty good...nothing crazy though. It saw 6,500-6,600 rpm about 6 or 7 times. I took him back to his car and it just died. It fired up initially and would die as soon as I touched the...
I've swapped several ported Eatons, but never a KB. I'm curious to know how different a KB install is compared to an Eaton.
I've done some searching and came up with bubkis. :read: I did find TooFast4u's KB Install Tips post which is helpful.
Does Kenne Belle have their install...
I'm trying to remove the lower intake. I have the blower/intercooler off the car. The lower intake seems like it'll pull right out, but I think there's a wiring harness fastened to it in the back. It's extremely tight back there (big hands) and I can't exactly see what's going on.
Anyone...
A buddy of mine was helping me install my Apten ported blower and he torqued one of the gold lower intake manifold bolts too much and it broke off in the intake. We were both being very careful too. :nonono: Anyone else run into this problem? If so, how would you recommend I go about removing...
Anyone looking for a UPR ORX pipe? It was on my car for literally 3 hours. I have 90% of the bolts that came with it. You could use a few of the stockers and be fine. I'll let it go for $100 if you pick it up. I paid $175 shipped.
Let me know...
Yes, I searched already. :bash: ;-)
I have the MGW handle right now mounted on a Pro 5.0 shifter. I have the Pro 5.0 shift handle in the garage. I'm considering going with the Triax handle. I'm starting to dislike the angle that the MGW handle is in in 2nd gear. If I recall correctly, the...
I'm with State Farm and I feel like I'm getting hosed. I have an Explorer, the Cobra, and a house on my policy and I'm still paying $186/month for the 'stang.
I called Allstate and they quoted $1,677 for 6months for the Cobra and $1,000 for 6months on the Explorer. :??: I'm 28. I figured I'd...
I'm installing a UPR ORX pipe tomorrow after work in the garage. I'm sure plenty of you guys have installed a midpipe. I'll turn off the rear O2's with the Predator.
Any tips?
Can anyone recommend a nice nitrous switch panel? I can't seem to find one. There's one stipulation. I won't cut any of the interior to mount it. I've seen one that replaces that gay little coing holder, but I have two switches and that will only accomodate one. I could fab one up I suppose but...