Search results

Found a used 2014 Shelby over the weekend, low miles, and sitting at a dealership. Current dealer tells me they picked it up directly from a invitation only Ford auction, and that the car was originally repurchased from another dealership by the manufacturer (Ford) in 2015 as-new. Ford kept the...

Just as the title says...looking for low miles, SVT pkg, etc. Coupe only. Cash in hand. Thanks!

I have a buddy who is 42, has a very successful business, and is wanting to purchase a new car- a "status symbol" car. He currently drives an Infiniti, but also has a GT500 that he drives on the weekends. He is selling both, and has narrowed his picks down to a Z06 Corvette, a BMW M3, a...

Looking to buy Eaton..PAYPAL preferred.

:banana: Trying to get this damn car back together. I can't figure out the reinstall position of my lowering springs. Bottom cup position had Factory pigtail end pointed straight towards the rear of the car on the pass side, pigtail end pointed towards pass door on the drivers side. What...

I am installing the MM CC plates on my Cobra, along with my lowering springs and have a question. First off, it shows in the instructions that only a "short" spacer goes under the bearing plate, while the remaining 2 long and 1 short go on top. I have seen a couple cars that have 1 long...

Finally got around to getting some pics of the Yokohamas I got from Matt at DTD. 275/35/18 Front, 315/30/18 Rear. Handles great, no road noise at all..very very nice. Yes, I know it needs to be lowered..I already have the Steeda springs..just haven't had time to swap them yet...

I have 2 nice OEM Ford Terminator R/L headlights for sale. They have a few very very small rock/sand chips in them, which are only visible when the headlights are on. I would rate them a 7/10. 45.00 each, or 80.00 for both plus shipping.

If so..how difficult was it? Any special tools needed? Took my car in for an alignment, and the shop said 1 outer tie rod was bad, and one inner tie rod was bad..they wanted 150 just to change the inner tie rod. :??:

Today is really the first day I've had my Cobra out in the high daytime temps in SC, so I wanted to data-log my intake and coolant temps. After sitting in traffic for about 10 minutes, the temps in the ECT log started climbing towards 220..then to 222 where they stayed until I sat in traffic...

Do you guys offer an SVTP discount code for ordering off your website? Thanks!

Can anyone tell me if running a 2.93 pulley (and correct tune) will cause any issues with highway trips? Issues, as in: overspinning the Eaton, gas mileage, drivability, etc? I want a little more HP, but I'm not interested in jumping up and changing fuel pumps, adding a KB, etc. If I...

I'm trying to figure out what color the carpet is in my 04. The interior dash panels/door panels are charcoal I guess..its not black for sure. Is the carpet charcoal, or is it gray? Is the trim listed on the door jamb?

The JLT RAI, or the K&N FIPK? They both flow about the same...but I keep reading the K&N offers a great S/C whine to go along with the increased airflow. Anyone?

I am curious as to how these pieces come off: First piece is the rocker/sill moldings. Are they glued on, or do they just use fasteners to keep them in place? Second piece are the REAR exterior A/Roof pillars. They look like they may be bolted on from the inside, but they may also use a...

Does anyone know if just the lens itself can be replaced on the Cobra, or does the whole assembly have to be replaced? One of my lights got popped with a rock, and is cracked now. :fm:

I have a set of struts/rear IRS Bilstein shocks for a 03-04 Cobra. Came off a 10,000 mile car, owner went to coilovers with upgraded shocks. My Cobra had brand new Bilsteins on it when I bought it, so I have no use for them. I took them in on a trade for some parts I had laying around...

I was doing some data-logging today on the car, and noticed when my car got close to turning the fans on (220 degrees), my Speedhut temp gauge read 230, while the tuner read 220. I was not driving the car, but just sitting there. The car was just idling for about 8-10 minutes, so the engine was...

I want to remove my quarter panel scoops on my 04 Cobra. Are these held in place by bolts, or do they just snap in? Can anyone tell me how to remove them?

Then maybe what I did will help you out. I ordered 8 new TR7's to go in my Cobra, and owning a Saleen, I already knew about the spark plug issues that Ford owners face when removing/changing plugs. When I upgraded my Saleen to JDM's Stage 2, my car had minimal miles on it. Luckily, the...

Just curious if anyone has hooked up, or is running satellite radio with the OEM Mach 460? I know they make an adapter for the wire harness, but I'm not sure where to get the factory tuner that makes everything "work". Whats everyone doing?

Can anyone tell me where to find the 4 digit computer ID code on my 04 Cobra? I don't even know where the computer is located. :shrug: Need it to give to Amazon Tuning.

Might be a dumb question..but I notice that when pushing in the clutch, my drivers seat makes a slight "clunking" noise..almost like somethings loose in it. Its more annoying then anything. The seat feels solid other than the noise it makes. I've checked the body mounting bolts, and they...

Just as the title says. Most 18x11's I see are all custom-made. CCW has about the best price for what you get, at least from my research. Its not that I mind spending the money, just wish there was something more affordable out there for a DD.

Not long ago, I stumbled across this http://www.svtperformance.com/forums/suspension-modifications-211/559777-anybody-experiencing-loose-play-steering-steering-shaft-suggestions.html thread and wondered if I had the same condition on my Cobra. I have had a loose, off center feeling in my...