Search results

Alright, built a brand new engine, Whipple 3.4 on top, aftermarket dual BB idlers, stock caged lower, RR manual tensioner, RR 4" upper. I have tried both Gates green belts, and Gatorbacks. I can't get consistent, not-dropping off boost to save my life. Either it peaks to 18psi, and RAPIDLY...

Looking for a 3.75" pulley for my 3.4L Whipple, don't really care what brand just lemme know what you have! Thanks!

I need all the hydro-boost/powering steering lines to finish my GT to Cobra setup conversion. I need the bracket and lines, but not the reservoir.

Reposting this because this shitty site apparently needs "http://" for image tags to work properly. Thanks for help with the previous post...

Hate to start another belt length thread but tons of searching has not yielded me an answer for this combo. 3.4 Whipple on a 03-04 Cobra setup Teksid block, stock lower, have all the Divixion X idlers including snub idler, with a 4" blower pulley. Thanks :) For reference the previous...

I'm putting a 4V termi swap in my GT. The guy I bought the blower off kept the IAT/MAP sensor. Now, of course I have no need for the MAP, is there a solution to put an IAT in the hole instead that will hook up easily? Or do I need to find one of those MAP/IAT sensors and just wire in the...

Need a set of rings for ONE PISTON from a set of CR8264-25. (or really just the top ring) Or willing to buy all 8 if you have a box sitting around. I bent one of my top rings installing just now. Furious. Thanks.

Looking for stock manifolds, in good condition with studs at "collectors".

Need a set of aftermarket rails for my Whipple 3.4. ORB-8 in out. Thanks

For use on a 3.4L (if that matters). Thanks!

1 3/4" primaries to 3" collectors with a 3 bolt flange. Driver's side collector has two bungs on it for OEM narrowband and wideband. Can include a plug if you only intend to use one bung. *EGR pipe not included. $700 + shipping.

Are the Comp 106400 cams suitable to be used with a 3.4 Whipple, 4.6 motor? Should I be looking for something better suited? Link to specs: 106400 - Xtreme XE-R Series

Looking for a 3.4L Crusher, black. Let me know! Thanks

Building my new teksid motor for a Whipple 3.4, realistic 700whp goals. Might put race gas in it one day, but lets not plan on that just yet. Going to be opting for the H13 tool steel wrist pins on Diamond pistons, but what wall thickness should I be going with, without being overkill? They...

Looking for a set of new or used 20 over pistons with 4V notches. In the 12 to 18cc range. Let me know if you have anything!

Not entirely picky about which manufacturer. Would like prefer the one that uses the rear freeze plugs though as the motor is out right now. Thanks.

Looking for an aftermarket harmonic balancer to be used with the caged outer OEM pulley system. Preferably Innovators West. Are there any others that make this?

What are the advantages of using a Metco lower over the OEM? Planning on a 3.4 Whipple in the mid-20 psi range. Trying to decide if I need one.

Innovators West 10% OD, 8-rib, Polished $350 shipped to Canada or US.

Something aftermarket, let me know what you have. Thanks.

Comp Cams Stage 2 Xtreme Energy XE270AH Camshafts (for PI heads) Details: http://www.summitracing.com/int/parts/cca-102600/overview/ $350 (gears not included) Cloyes Hex-A-Just Adjustable Cam Gears $200 (Will work out a deal if you want the cam gears and the cams) RAM pressure...

Got the opportuniy to attend the launch festivities at the Ford Conference centre today, pics below.

Looking for a tubular K-member with a-arms, for a 1988 Fox body with a factory pushrod 5L. The newer and cleaner the better! Would be nice if it had the coil over kit, but I can source that elsewhere if needed.