hey ladies and gentlemen. its been awhile since I have been on here. we had a baby, and purchased a new house so we have been super busy!! I am on Instagram more often if anyone wants to chat. ( @03svtjmc ) figured id make a post anyways !!
I am super excited to share that I pulled the...
New personal best yesterday in the street car. I’ve put hundreds of street miles on it this season cruising the streets in Michigan. It’s not a daily just a toy I take out for fun. I did trailer it Incase something happened. First pass off the trailer soft hit, went..
22lbs of boost, 16 degrees...
new motor, first fire up.
romeo block, standard bore
diamond pistons 10.1:1
molnar turbo rods upgraded h13 .200" pins
arp2000 rod bolts/ head studs
cobra crank
livernois ported heads, stainless valves & pac springs
todd warren specd bullet cams
CG FAB hot side single bullseye 80mm turbo...
This past September I spun a rod bearing in my turbo 03 cobra. at that moment I was not very excited nor was I thinking properly. I was pushing car into garage and then I heard a SNAP. I look down and to add to my F*CKERY of a day, I was pressing on the 3rd brake light. this resulted in a couple...
well this starts as I took my coil pack covers in to get powder coated. when he sand blasted the old powder coat off. he had the regulator set at 200psi and it melted the corners folding them over.. so I went and picked them up after the fact they didn't like the idea what it cost to replace...
so last year didn't go as planned. as i wanted to run a 8.99 with a factory longblock other then head studs. well, i broke the factory oil pump gear as i was stupid and did not put a billet one in. oh well it was a good time to build a motor. here is the run down on the new motor.
factory romeo...
so last year didn't go as planned. as i wanted to run a 8.99 with a factory longblock other then head studs. well, i broke the factory oil pump gear as i was stupid and did not put a billet one in. oh well it was a good time to build a motor. here is the run down on the new motor.
factory romeo...
hey everyone I'm planning to switch over to holley EFI. along with building my new motor. so that will all depend on the funds throughout the build! but meanwhile I'm been thinking and curious if anyone runs gt500 coil packs? ive heard rumors they can handle more power then the stock cobra coil...
its been a little while since I have posted about the 66 mustang build. ive had the car since 2008. finally after years I had the money to restore it. some of you may have seen some of my turbo cobra pictures ive built the last couple years. I also have been building this 66 for 2.5 years. its a...
its been awhile since I have posted. last time I posted it was on the new turbo setup. still factory long block other then head studs. upgraded to a 8087 Bullseye turbo, did scott rod panels. was hoping to break into the 8's this year with this setup but it did not happen. I ended up breaking...
just finished up the new setup. still a Stock bottom end 03 cobra. Arp Headstuds, e85, 25lbs, 16 degrees timing. 4r70w, bullseye 80mm batmowheel 1.0AR T4. Cg fab hot side. garage built cold side and bumper exit done by myself. edelbrock elbow with acufab 90mm v band throttle body, and scott rod...
still running the CG fab hot side, twin 46mm wastegates. new turbo is a bullseye batmowheel 80mm. (80/87) t4, 1.0AR. fitment is awesome with the custom radiator.
off my cobra with 48k miles, went manual brakes and custom radiator/ fans. these work perfectly and are in great condition.
Fan- $100
hydroboost/master cylinder- $100
call/text- (810)444-756four
thanks jeff.
custom radiator a local shop (dewitts radiator in howell michigan) built for me. fits in factory radiator mounting without the a/c condencer because it sits up flush with the core support. its a 2 core, diffirent variations can be done as far as fittings, fill tube, temp sensor, ect. ect. i...
i bought a sullivan lower, berry motorsports billet upper elbow, and acufab vband throttle body. would like to see how some of you ran your cold side piping forward. not sure if im gonna run it forward or modify the elbow so i can bolt it on sideways to run piping on the passenger side.
thanks! :D
99-01 cobra
03/04 mach 1
throttle cable for sale, no cracks in outer layer covering cable. no freys in line. mint condition.
$175 shipped.
(810)444-756four
thanks jeff
I'm making some changes this winter. I am running a precision 7675 .96 a/r billet wheel. I been looking at the bullseye 80mm batmowheel. Curious if anyone is running the bullseyes or what is everyone else running? Mind isn't made up yet, I may stay 7675.
Thanks!
hey everyone. so here in michigan, winter is right around the corner. which means cold cold weather and alot of snow (hopefully). the last week i tackled this project of getting these scott rod panels installed. i wanted a little kick start before it gets to cold and harder to lay the paint...
couple photos from this past friday. kid at a car show came up took a photo, i was impressed with it so i gave him the opportunity to take some more and they turned out good i thought! kids name is TJ, tjsphotography local here in michigan. not bad for 16 years old! better then i can do!
this past sunday Ctgreddy and i went to mustang memories in dearborn michigan had a good time!! awesome turnout and over 800 pre registered cars is what i was told. the first couple photos are our cars ( colins black kb cobra and my turbo sonic blue cobra).