I had a Zinc Yellow Terminator Cobra and followed alot of Facebook group pages, Instagram and Termi forums. I remember there used to be a guy who would repaint diecast model cars to the exact spec you had if you sent him a diecast car.
If anyone knows or remembers, can anyone point me in the...
Wow!!! Very educational man. Thank you for this explanation, 3 years later I see this and it's still helping people. I am definitely looking at buying these when comes time to change brake pads in my 2017 GT350R. I don't track my car, mostly a weekend cruiser but most definitely want this...
What size up front did you end up with?
I think currently I have 245/40/18 with my nittos. I have had my front end aligned and checked most front suspension components but get a definite vibration at speed. Another reason why I am changing out the fronts. Ibbet I've had my fronts for 7+ years...
What size up front did you end up with?
I think currently I have 245/40/18 with my nittos. I have had my front end aligned and checked most front suspension components but get a definite vibration at speed. Another reason why I am changing out the fronts. Ibbet I've had my fronts for 7+ years...
I have a 2003 Mustang Cobra, I have been running Nitro NT555 front tires (18") for a number of years. I put very few miles on the car which has been beneficial at getting long life. However, it is finally time to upgrade to a new front tire. What has everyone been having luck with? Michelin...
I have a couple different Mickey Thompson drag radials currently.
15x10 Racestars wheel + 275/50/15 Mickey Thompson et street radials.
25.5" tall.
18x10 Cobra R Motorsports + 315/30/18 Mickey Thompson et street radial 2.
25.5" tall.
Does anyone else have a wheel/tire combo heights for other...
Had a remote tune session down in Indianapolis with Bob Kurgan this past Monday. I strapped down at Cozzolino Motorsports, had Larry Thomas behind the wheel.
My Cobra is an 2003 with basic bolt ons:
Stiegemeier Stage 5 port
BF 2.9 upper
LFP 4lb lower
LFP single blade TB
Accufab...
I purchased a LFP 4# quick change pulley setup for my 2003 Mustang Cobra.
I have a 2.93 billetflow upper and a 100mm idler pulley and switched to a bigger Alternator pulley 3.50". LFP had sent me a Gates belt with a 1-3/32" x 79.5" OC, this was TOO SHORT. I wanted to share that I did mount...
I am getting ready to switch over to E85, I live in Indiana so finding a E85 pump shouldn't be hard.
I have 80# injectors, SCT BA3000 MAF, KB BAP and wireharness upgrade along with a lower 4# pulley, a LFP single blade TB and a Accufab ported elbow to install.
Should I run a tank of 93...
I am getting ready to install some new parts on my 2003 Cobra in hope to have it tuned to E85 by Bob Kurgan. One of my mods is getting the KB BAP and wire harness upgrade installed, I am curious to which is better? Installing the BAP before the FPDM or after the FPDM, I wasn't sure the...
I was curious if anyone knew of or had good experiences tuning for the 03 cobra. I had my car tuned at Brenspeed in 2010, however they no longer touch cars older than 2005.
I am in the process of adding some fuel upgrades to switch to E85 and a lower 4lb pulley.
Any help in locating an...
I currently have a catted x pipe on my 2003.
I think I want to convert, to a off road x pipe instead, will I need to have my car retuned for this change?
What brand do you guys recommend, any advice would help narrow down what im going to purchase.
I have an 03 Cobra with the notorious head tick coming from the driverside head. My car only has 36K miles with the stock heads.
I am curious if I can have these heads overhauled, then put in the head cooling mod, to fix these heads?
Is this even possible, will I still have the ticking...
I'm selling my stock 20x8 Harley Davidson Edition wheels that came off my 2008 F350.
These rims are used and show some wear, I have all 4 centercaps and lug nuts to go with. The rims have Bridgestone Dueller AT tires on them that have over 75% tread left.
EBay has the same style used rims...