Opinions on fore fuel system for e85 kb2.8 and install
- Thread starter blwn03sonic
- Start date
That looks clean. I’ll have to check how to do that since I have access to the inner fender right now.
Sent from my iPhone using the svtperformance.com mobile app
Got the metco lower pulley kit on. Stock lower came off pretty easy.
Sent from my iPhone using the svtperformance.com mobile app
Sent from my iPhone using the svtperformance.com mobile app
Mounted the fc2 controller using the old holes for the fpdm bracket.
Sent from my iPhone using the svtperformance.com mobile app
Sent from my iPhone using the svtperformance.com mobile app
What fuel lines are those? PTFE I hope.
Sent from my Moto E (4) Plus using the svtperformance.com mobile app
Sent from my Moto E (4) Plus using the svtperformance.com mobile app
Flex LP as suggested by my tuner.
Sent from my iPhone using svtperformance.com
Sent from my iPhone using svtperformance.com
Yes if you don't want fuel smell.
Sent from my Moto E (4) Plus using the svtperformance.com mobile app
Haha this is an argument I had with a big name vendor years ago. Now their kits have PTFE lines...
I’m going to look into getting the lines in the ptfe stainless braid. These are the ones that were ordered with the kit.
. I started the car yesterday with the base tune and it idled great no leaks. It has a 4K limiter for the time being. I’m going to go through a couple tanks do e85 change the oil and the plugs once more and get ready for the tune in November.
Sent from my iPhone using the svtperformance.com mobile app
Sent from my iPhone using the svtperformance.com mobile app
Does the hose have a hard plastic liner inside?
Sent from my iPhone using svtperformance.com
Sent from my iPhone using svtperformance.com
I’ll have to check when I get home. I have some spare hose I was going to use for my catch can.
Sent from my iPhone using svtperformance.com
Sent from my iPhone using svtperformance.com
I do not believe that is PTFE hose. I did not think Fore had black PTFE line so I ordered mine through summit.
This is what i used in my engine bay.
https://www.summitracing.com/parts/fra-601028/overview/
This is what i used in my engine bay.
https://www.summitracing.com/parts/fra-601028/overview/
What fittings did you use with that hose.
Sent from my iPhone using the svtperformance.com mobile app
Mostly Fore fittings but I did order some additional Fragola PTFE fittings. Fore and Fragola are probably the best in the business.
I had two of these for the balance line in the rear of the blower
https://www.summitracing.com/parts/fra-684508-bl
one going to the y-block and two leaving the y-block. I did not have the F4i regulator.
https://www.summitracing.com/parts/fra-680108-bl
two of these for the fronts of the rails.
https://www.summitracing.com/parts/fra-681808-bl
Adding that hose does not bend as easy as the FlexLP hose.
I had two of these for the balance line in the rear of the blower
https://www.summitracing.com/parts/fra-684508-bl
one going to the y-block and two leaving the y-block. I did not have the F4i regulator.
https://www.summitracing.com/parts/fra-680108-bl
two of these for the fronts of the rails.
https://www.summitracing.com/parts/fra-681808-bl
Adding that hose does not bend as easy as the FlexLP hose.
Thanks. I’ll have to make this a future project. Wish I would just ordered the ptfe lines from the beginning
Sent from my iPhone using the svtperformance.com mobile app
My rails are capped in the front and feed through the back.
Sent from my iPhone using svtperformance.com
Sent from my iPhone using svtperformance.com
I prefer Aeroquip over Fragola. I did a complete custom setup using lines from www.Aeroquip.cc great site great prices. I have been running Aeroquip since 2012 and not the slightest sent of fuel.
Users who are viewing this thread
