Got my car back from Manny at Dasilva Motorsports, car made 582 WHP and 556 lb/tq at 9 psi. Will see how it runs when I get it back on the road later this month, once all the snow is gone. I found out that my SHM 2.3 TVS blower is really a Magnuson unit that has a Sean Hyland sticker on it...
Picked up my car on Friday from nearly 5 weeks of being at the builder. the motor is a stock block 2014 with lowered compression 9.6:1, fully built bottom end with billet oil pump gears abd an 82mm pulley TVS setup. On the drive back from the builder I notice a smell and smoke out of the...
For those not familiar with my story I threw two rods and punched a whole in the block 3 months ago on the stock motor with a Roush blower.
I got my new motor installed and running finally. I bought a stock 2014 motor and had forged internals stuffed inside, billet oil pump gears and dished...
I have a new fully forged bottom motor on tap (Manley rods, pistons and forged crank 9.6:1 compression) with a TVS 2300 at 12 psi, not sure of the pulley diameter as it is a SHM blower. Am I unreasonable to expect 600 as the wheels and 500'ish torque?
Mods are as follows:
- Catted Steeda...
[B]Please note blower needs to be rebuilt, lobes are seized after motor failure. Intercooler has been cleaned out, but needs to be professionally cleaned prior to use![/B
Will part out or sell complete.
- Roush TVS 2300 compressor - snout is fine but lobes are seized in housing
-...
So two weeks ago from Easter Friday I was driving my car home from work logging some miles on it prior to getting my new catted X-pipe and Roush axle back exhaust installed and my motor threw two rods.
I had it towed to a local shop, they took the motor out and dug into it. Ends up two rods...
Got the car on the a dynojet this afternoon. It made 525 RWHP and 502 lb/ft of torque. I will be trying to get it to the track next weekend weather permitting. Anyone else out there running the 2.3 TVS to compare numbers with?
Well I finally made it out to the track with my 2010 GT and I got my buddy with a 2007 C6 to come out as well, he has a full race Corsa exhaust with X-pipe.
Anyway we both haven't been to the track in iver 6 years, so needless to say we both sucked. His 1st pass was a 16.2 and mine was a 13.5...
I just purchased a Grabber Blue 2010 GT from my neighbor at a local Ford dealership. Car has 3.73 gears, the factory option P245 ZR 19 Pirelli's, 5 PSI from an M90 Roush supercharger, cat back Roush exhaust (which is heavenly BTW) and a CAI with a tune. I have not had it dynoed as of yet.
Any...
Could someone please tell me if this is an M90 or a TVS Roush blower? I test drove a used 2010 GT with a factory installed Roush blower and exhasut. Holy low end torque, kicks the crap out of my old 2002 GT.
Anyway I am thinking it is likely the base M90 kit because I did not see an...
I am looking for a lower mileage cobra in the north/east USA or Canada. It would be preferable to have fewer mods, I am not looking for an abused car.
If there is anyone in the market PM me or drop me an E-mail at [email protected]
Hey all,
I am looking to add some unnatural aspiration to my 5spd 2002 GT soming up in the early summer when my bumper to bumper warranty expires. I am looking for people to tell me about their experiences with installing an S-trim SQ on their cars. Any problems you had, how do you like the...
Hey all,
Sweet assed, I figured out my 1st post on my lunch break!
I have a good buddy with a mildly moddified 97 6spd black Z28SS, I have a stock 2002 5spd GT (sans air silencer, with KN filter). Anyways he has a full corsa exhaust, 1-1/2 equal length headers, 2.5 inch Y-pipe, ans 2...