The set up is far from stock, I have a Shelby m122 on it with an adapter plate and a separate cog drive. It worked well for a while then when I turned up the blower Snout snapped then I machined a new one and it started snapping belts. I also had made mounts to put the Alternator where the A/C...
I see what your taking about and I completely forgot the lower has literally no runner length.
That's likly going to be an issue just as much with the turbo set up as it would be with Centri.
I tried to find some info on his centi set up but found it hard to keep up.
Do you know if he...
Did a search but can't seem to find anything that was completed and working .
Trying to decide between a turbo or procharger set up.
Anyways. Can get a deal on some 60mm gen 2 new turbos. I've tried to keep up with the sizing but I get lost
Compressor is 60, turbine 62, A/R .68
Would like...
I appreciate the advice but when I freshin up the motor with my high comp boost pistons I'd like to turn it up to silly power. I have friends with supras.
I think the car would be awesome with a whipple and e85 but I can't get e 85, I had it on my last set up and the e85 would go bad before i...
Been out of the game for a long time, a little back storey. My car is a vert, full suspension, mini tubbed, narrowed 8.8 with 9" ends, was manual brakes and steering.
I pulled it apart to put a proper cage, new high comp engine 88 turbo, TH 400 but then didn't have the heart to cut up the car...
So. Long and short. cars been off the raod for three years do to personal issues in my life. I've finally got her running again but need a set coil packs. I can sense a miss in 1 plus the last time the car was at the track I had a lot of issues running e-85...
So, I can get a set of LQ9 coils...
I have a 10 spline input shaft with about 4000 miles 75$ obo
03 cobra Flywheel with about 4000 Miles, will need to be resurfaced as I murdured a centerforce on it. $obo
Stock 03 cobra clutch and pressure plate with only 3000 miles. Good clutch, held an 11.0 and seems to be much stronger...
39lbs injectors less then 5000k's. 100$ plus shipping 03 cobra clutch less then 5000k's. Best offer, intake plenum best offer. I'd you want to do your own port work I can weld it up cheap then port it your self). Blower bracket that holds the sensors with sensors new but 1 has a crack. Best...
I have the mid plate for a lighting. I bought the full swap but used the intake to make a custom 2v eaton swap. I just gave the manifold
Looking for best offer. I can ship out friday other wise it will have to be shipped from canada
I have a 2.6 pulley and hub, best offer no low balls, came with my M122 blower but ended up going to Cogs.
I can ship from Canada or I can drive accross the boarder and ship from michigan. All depends on how long you want to wait ect But I ll figure out cheapest ect for you..
Thanks Jim
Ok, To start off I live in canada soo, If your in a rush I can send them from here or if you can wait an extra couple days I can send them from Michigan for a lower rate since I m back in forth all the time. I can send it from canada at 0 dollar to avoid the extra cost or possibly send it from...
Came close, did a run to check the tune, no ice running hot and it ran 11.07 then let it cool off and packed it with ice and it blew the clutch.
Hoping to get a new clutch in ASAP and try some dry ice with some cooler weather. Really trying for the 10`s on this stupid thing.
aCiD99GT's...
Got a hold of some vids that someone ealse took.. Wish I gad a go pro lol.
This was pump gas, and street mode other then my cat back off and slicks ported eaton only..
Still want to hit a 10.99 before the years out. I ran a 11.2 @ 124 with a 100MPH 1/8 mile and a 11.3 costing thru 4th...
Went to a grudge day and hit the magic number.
It was warm out and my IAT's were thro the roof but the car laid down a 11.42 @ 122 with a 1.69 60 foot.
The car started pulling timing on the top end, need to figure out what happened to the inter cooling system. I normally don't go over 140...