Post your Shelby GT500 Dyno Numbers in here

[ericmuscle]

numbers in sig.

 

[RI GT500]

VMP Gen 2
2.4 pulley
FRPP65mm throttle body
JLT127mm CAI
Dtnatech longtubes
Dynatech O/R H-pipe
56 lb. injectors
VMP boost-a-pump
170* thermostat
C&R dual fan heat exchanger

684/711
View attachment 41050

I have almost the same combo. Accept I have FRPP shorty headers, off road X, and a IDT 1000's and a 4R75W trans with lock up converter. I'm hoping for 650/680. we will see Tue.

 

[RI GT500]

It turned as expected 648 hp 618 tq, I would have thought more tq, but overall happy. Hopefully get to the track soon.

 

[CentralTexHemi]

VMP TVS 2.3
ID 1000
VMP BAP
90 mm idler pulley
BPS Aux idler pulley
Thump belt tensioner
JLT 123
BR7 plugs
Lethal Performance DivisionX 1400HP return style fuel system (E85 approved)
All UPR suspension
Tokico D Specs
Ford Racing lowering springs
C&R Dual Fan HE
AR 1 7/8 Long Tube Headers (no cats) H pipe / stock axle back
Dynotech 1 pc alum driveshaft
Moser 31 Spline Axles (tubes welded)
TruTrac limited slip
McLeod Dual Clutch
MGW shifter
ATI 15% OD pulley

Tuned in Texas heat (106 degrees)

 

[dsweet]

see signature for mods.
on 116 fuel / 21PSI and a DynoJet - made 820RWHP and 744T
on 93 fuel / 19 PSI same dyno same day made 762 RWHP Torque was not shown

Stock Internals

 

[hydro]

2007

 

[Maxpowers]

2011 - Bought the car last month. Unknown mods past visual inspection.
2.8" Upper
10% Lower
JLT Intake
Muffler deletes
Lund Tune

 

[hydro]

2007 GT500 Lots of Porting L&M Throttle Body

View attachment 834 (1).pdf

 

[genesmob]

2007 gt500 convertible
VMP gen 2 2.5 pulley
10% balancer
Stock injectors reflowed to 72lbs
VMP bap
Dynatech headers no cats
VMP big h/e with fans
FRPP monoblade
JLT 127mm carbon intake
FRPP rearend 3:73
Al driveshaft
NT555rs
19lbs of boost
18 degrees of timing
93 octane with torco
Tuned by BJ @VMP
742RWHP sae at 6200 rpm yesterday at LRS/ASSC dynojet

 

[stuck in Laredo]

I just got my '08 GT500 back from Maximum Velocity in San Antonio where they installed the following:

'14 Trinity TVS with 2.4 pulley
Ford Racing CJ 65mm throttle body
JLT CAI
'14 56 lb injectors
Kenne Bell BAP
Steeda triple pass HE, 3X reservoir, 170 degree thermostat
Kooks headers, O/R H pipe and Borla Touring catback
MGW Gen 2 shifter
DSS carbon fiber driveshaft
BMR UCA and LCAs

Jon Lund remote dyno tune made 692 horsepower - 652 torque on a Mustang Dyno

 

[hotford]

well not mine but a close friends
2013 GT 500
kooks L/T, OR Mid pipe, flow masters
10 overdrive.
VMP pulley(2.4) and inlet belbow
VMP modified twin 62mm TB
Stage 4 crower cams.
16 psi
93 octane
15 degrees total timing
809.82 rwhp,758.48 rwtq
yes the blower is still stock.......

dyno is set to SAE if your all wondering......next up E 85 tune!!!!

rechecked the tune two weeks later and the car made 811 rwhp...lol

 

[shelbygt500_897hp]

664 rwhp with copius mods

don

 

[MDShelby]

Added NSR cams and ID 1000 injectors to sig description.

 

[Assman]

Put my stock 2011 on the dyno yesterday, it put down 496 on a dynojet. The torque didn't show up unfortunately but I was quite pleased with it. Once the snow flies I'll get to modding!

 

[2010 Red&white]

very nice numbers....looks like Jerry's and Lidio's ..??

 

[70SCJ]

Built 5.8L
VMP Gen 2
VMP dual 67 mm
2.4 pulley, 10% ATI
Stage 3 cams
JLT 127 mm
Dynatech longtubes
E85
17.5 psi

 

[Bryan Raby]

2007 gt500. 743whp /733

743whp 733 tq



Mod list

-2013 gt500 2.3 tvs blower swap
-10%ati overdrive balancer
-Boost a pump -kb
-Stainless works long tube headers
-Ace twin disc clutch
-Aluminum one piece drive shaft (from Shelby)
-Mgw short shifter
-Id1000 injectors.
-Ford racing oval throttle body 168-170mm I believe
-Jlt cold air intake
-Stainless works X pipe
-Corsa extreme exhaust
- Lund racing custom tune.
-Shelby competition heat exchanger
-Bmr 1.5 " lowering springs
-Viking double adjustable rear shocks
- Koni yellow front struts
-Bmr watts link assembly
- Bmr billet aluminum rear lower control arms
-front lower control arms
lower control arms
-Nitto nt05r drag radials

 

[tangermean]

2010 gt500

2010 GT500 30,000 miles only mods are FRPP resonator delete and pypes axle back mufflers (I hate them)

Car made 481 RWHP ignore the RPM I didnt get it hooked up right.

 

[strokedtermi03]

2010 Shelby 685RWHP/ 701ftlbs tq.
Car has 2.3 tvs , 2.4 upper pulley , 90mm idler, id1000 injectors, Kb BAP,lethal o/r X , flow master axle backs,123mm Jlt CAI , tuned on E85 . Have AR long tubes waiting to install, and twin 67mm VMP TB.

 

[Sirhc7897]

2011 GT500:
-VMP Gen 2 TVS
-2.4 upper
-170 t-stat
-C&R heat exchanger
-JLT 123
-VMP 67mm throttle body
-56lb injectors
-VMP fuel pump booster
-Stainless works full exhaust (orx)
-RXT twin disc