* This is a Dupe post from another forum but I was here pounding keys a whole lot as well !
I've posted or participated in every Mono Blade thread with curiosity then frustration about the FRPP SCJ, after 2 anchored Mustang Shop failed street driveability tunes + a failed Lund tune. One SCJ pulled 17rwhp but could not idle....hysterical !!
With the Two SCJ's ...both dated early 2016...TONS of calls to Ford Tech/Accufab (who's bench test declared mine to be perfect) both SCJ's now GONE. I can tell you I found a Mustang race shop just a couple of weeks ago...who has an original, unopened 2012 Ford SCJ and came very close to jumping on that deal and SCJ #3. If anyone is interested in that lead please PM.
Rather than revisit the SCJ nightmare I followed Jon Lund's April then most recent advice and finally ordered the Power By Hour package. This includes the huge KB 168mm Mono Blade, KB bolt matching O-Sized XBA Plenum and huge JLT 148 CAI. BPS makes the XBA and having the BPS already this was a dead port match for my Trinity.
After install in my garage and 8-9 street data logs Jon Lund Jr. did the final tweaks. My GT500 purrs at 850-900rpm at idle.....pedal's smooth as silk thru town ...zero surge....decells smoother than my twin blade which (with headers) had some slight popping. On the stab ...anywhere....throttle response is instantaneous and pull is linear. But hey...what does my butt know ? Let's compare to a late August Lund tune twin blade dyno pull.
Back in August I was at 2 shops advice hopping about a 10% crank pulley. I had room because my boost was 16.3 psi ...likely due to good breathing exhaust. On the Mustang dyno at 16.3 psi boost it pulled 629 rwhp with 410 gears. On a Dynonometer 15 minutes away this same set up pulled 680rw at 16.5psi. After speaking with both shops rather than the 10% pulley I opted for the Lund tuned PBH package.
Yesterday on the Mustang Dyno the KB168/ XBA/ JLT148 gain was across the board with peak up 29RWHP + 17RWTQ. And...most important ? The boost was exactly the same (16.3psi) with the big KB168 JLT148 versus the twin blade JLT123. NICE !!! Here's the dyno sheet showing the 2 pulls 4 weeks apart . The dotted line is Twin 67/JLT123. Solid is KB168/JLT148. Can't kick about such gains. At Mustang Dyno 658rwhp would show low 700rw on the Dynonometer with the 410's . No gear change though !
I didn't know Jack-s--t about TB servo transfers from my old stocker to the KB. The guys at PBH were too awesome despite my pestering them about that, XBA plenum fitment slightly bending my fuel rails and other amateurish questions. Owner Frank is phenomenal and their tuner Jake always took time to give install advice. Jon Lund Jr simply rocks..........not much more I could possible say about him. I'm in mid 60's The kid trained me on everything from tune loads to data logs. I’m not promoting anybody here. My car has the VMP Stage 4…has had VMP tunes. As I modded.. multiple Mustang Shop custom tunes. I went to Lund trying to dig my way out of the SCJ mono ditch then kept his VMP 67 tune.
In the end I just wanted to tell you folks ....this combo works . And according to my monitor it passes all NYS emissions.
I've posted or participated in every Mono Blade thread with curiosity then frustration about the FRPP SCJ, after 2 anchored Mustang Shop failed street driveability tunes + a failed Lund tune. One SCJ pulled 17rwhp but could not idle....hysterical !!
With the Two SCJ's ...both dated early 2016...TONS of calls to Ford Tech/Accufab (who's bench test declared mine to be perfect) both SCJ's now GONE. I can tell you I found a Mustang race shop just a couple of weeks ago...who has an original, unopened 2012 Ford SCJ and came very close to jumping on that deal and SCJ #3. If anyone is interested in that lead please PM.
Rather than revisit the SCJ nightmare I followed Jon Lund's April then most recent advice and finally ordered the Power By Hour package. This includes the huge KB 168mm Mono Blade, KB bolt matching O-Sized XBA Plenum and huge JLT 148 CAI. BPS makes the XBA and having the BPS already this was a dead port match for my Trinity.
After install in my garage and 8-9 street data logs Jon Lund Jr. did the final tweaks. My GT500 purrs at 850-900rpm at idle.....pedal's smooth as silk thru town ...zero surge....decells smoother than my twin blade which (with headers) had some slight popping. On the stab ...anywhere....throttle response is instantaneous and pull is linear. But hey...what does my butt know ? Let's compare to a late August Lund tune twin blade dyno pull.
Back in August I was at 2 shops advice hopping about a 10% crank pulley. I had room because my boost was 16.3 psi ...likely due to good breathing exhaust. On the Mustang dyno at 16.3 psi boost it pulled 629 rwhp with 410 gears. On a Dynonometer 15 minutes away this same set up pulled 680rw at 16.5psi. After speaking with both shops rather than the 10% pulley I opted for the Lund tuned PBH package.
Yesterday on the Mustang Dyno the KB168/ XBA/ JLT148 gain was across the board with peak up 29RWHP + 17RWTQ. And...most important ? The boost was exactly the same (16.3psi) with the big KB168 JLT148 versus the twin blade JLT123. NICE !!! Here's the dyno sheet showing the 2 pulls 4 weeks apart . The dotted line is Twin 67/JLT123. Solid is KB168/JLT148. Can't kick about such gains. At Mustang Dyno 658rwhp would show low 700rw on the Dynonometer with the 410's . No gear change though !
I didn't know Jack-s--t about TB servo transfers from my old stocker to the KB. The guys at PBH were too awesome despite my pestering them about that, XBA plenum fitment slightly bending my fuel rails and other amateurish questions. Owner Frank is phenomenal and their tuner Jake always took time to give install advice. Jon Lund Jr simply rocks..........not much more I could possible say about him. I'm in mid 60's The kid trained me on everything from tune loads to data logs. I’m not promoting anybody here. My car has the VMP Stage 4…has had VMP tunes. As I modded.. multiple Mustang Shop custom tunes. I went to Lund trying to dig my way out of the SCJ mono ditch then kept his VMP 67 tune.
In the end I just wanted to tell you folks ....this combo works . And according to my monitor it passes all NYS emissions.