NO LONGER FOR SALE. I am listing up for sale my recent project car of over 6 months. I have put a ton of time, effort, and money into this car as you can see. I purchased the car as a roller and spent numerous hours tracking down all of the parts needed to make this car complete again.
This particular example is #1441 of 3768 Cobra Coupes and 1 of 281 in Competition Orange. The miles on the chassis is 75,000 and the engine has roughly 100 miles on it since it was completely rebuilt. The car is still on a base tune and needs a little bit more easy street driving before I would feel comfortable putting the car on a dyno and finalizing the tune. The car runs and drives great. I have not gotten into much boost to be on the safe side. I always try to be as cautious as possible when breaking in a new engine. I have performed two oil changes on the car so far and still have the oil/filter from the last oil change that a potential buyer is welcome to inspect.
This car has had extensive custom work performed on the engine bay, firewall, front crash bar, and lower radiator support. The engine bay was smoothed (the original panels were not completely cut out as some people do), a custom tubular radiator support was added, and a custom crash bar/intercooler mount was made. This work took a long time to complete as it was not just ordered from somewhere… everything was custom made specifically for THIS car. As far as I can tell, the roof, rear bumper, quarter panels, and trunk are original paint. The rest of the car was repainted or at the very least blended at the time of the engine bay smoothing. The body of the car is perfectly straight, no dents or dings anywhere. The ABS system was deleted and the car has custom tucked brake lines that run in the transmission tunnel instead of everywhere that is visible like factory. It has a Wilwood adjustable proportioning valve to adjust brake bias. The factory hydroboost is retained and all of the lines were converted to AN fittings/hose from Russell (not cheap!). The body harness is tucked completely out of sight and the fuse box is custom mounted in the drivers side inner fenderwell as are the rest of the control modules/relays. The harness has NOT been hacked up and is still completely intact. Horns still function and even the windshield washer wiring is still intact. The inner fenders do indeed still fit in the factory locations. The radiator is tucked to under the radiator support and has custom mounts. The more you look, the more custom things you find that have been modified or hidden as you look around the engine bay.
The engine from bottom to top is setup as follows, all machine work performed by Kevin Mullins of TKM Performance
Teksid block, stock bore
Kellogg Crankshaft, unturned
Carillo I-beam rods
CP pistons
GT500 windage tray
ARP main studs and main cap bolts
King racing rod bearings
Clevite main bearings
HEAVILY ported 9 thread 04 Cobra heads
1mm oversized valves
Ferrea valve springs, guides, keepers, retainers
New OEM lash adjusters
Melling billet gear oil pump
Ford Racing Timing kit
MMR billet passenger side secondary tensioner upgrade
Upgraded 8mm timing guide dowel pins
Crower Stage 3 cams
Cams degreed properly
MLS head gaskets
ARP 2000 head studs
2.76 pulley on stock blower
Kooks longtubes
Kooks x pipe
Polished Borla catback
JLT Intake
Simens Deka 60lb injectors
SCT BA3000 MAF
SCT handheld tuner, base tune done by Carolina Speedworks
Afco heat exchanger
Brand new Bosch IC pump
ON3 coolant crossover delete
SVE aluminum radiator
Transmission:
Stock T56 with Liberty 26 spline input shaft upgrade
SFI approved flywheel
Mcleod RXT twin disc clutch
MGW shifter
Royal purple fluid
Suspension/brakes:
Powerstop slotted/drilled zinc plated rotors
Orange painted calipers
Eibach springs
Wilwood proportioning valve
Maximum Motorsports CC plates
Misc:
SVE Series 2 wheels
Mickey Thompson 305 drag radials
Double din head unit
Battery relocation done as clean as possible
HID headlights and foglights
LED interior and license plate lights
All custom aluminum overflow/reservoir tanks
EGR delete
Rebuilt oil cooler
This isn’t your average 04 Cobra. It will be a focal point of any Mustang meet and draws a ton of attention. The engine was built with making 1000+RWHP in mind and is ready to handle that with a power adder of your choice. The car runs and drives very good as it is, but like I say the tune isn't spot on and it will need a final tune.. I figure whoever buys the car will probably want a bigger blower on it anyways. The only BAD thing that I know of is the car does not have AC. The firewall was smoothed and the holes for the evaporator were deleted. You could put AC back on the car, all wiring is still there and I have some of the components, but you would have to take the dash out to find/ recut the holes and install the evaporator. Heat works great as does the rest of the power options, even cruise control. The pictures speak for themselves as to the condition of the car. The interior is very nice and all of the seats are very nice with the exception of the usual wear on the drivers side bolster. I would rate the engine bay a 9/10 and the exterior of the car a 9/10 as well.
NO LONGER FOR SALE. $30,500. Not looking to trade at the current time. The only reason I'm selling is I enjoy building the cars more than driving them and I've ran out of things to do to this one, lol. Just looking to free up some garage space and money for new projects.
DSC_0701 by Ryan Bailey, on Flickr
DSC_0746 by Ryan Bailey, on Flickr
DSC_0748 by Ryan Bailey, on Flickr
DSC_0750 by Ryan Bailey, on Flickr
DSC_0751 by Ryan Bailey, on Flickr
DSC_0754 by Ryan Bailey, on Flickr
DSC_0763 by Ryan Bailey, on Flickr
DSC_0764 by Ryan Bailey, on Flickr
DSC_0765 by Ryan Bailey, on Flickr
DSC_0770 by Ryan Bailey, on Flickr
DSC_0775 by Ryan Bailey, on Flickr
DSC_0780 by Ryan Bailey, on Flickr
DSC_0785 by Ryan Bailey, on Flickr
DSC_0787 by Ryan Bailey, on Flickr
DSC_0788 by Ryan Bailey, on Flickr
DSC_0792 by Ryan Bailey, on Flickr
DSC_0793 by Ryan Bailey, on Flickr
DSC_0794 by Ryan Bailey, on Flickr
DSC_0798 by Ryan Bailey, on Flickr
This particular example is #1441 of 3768 Cobra Coupes and 1 of 281 in Competition Orange. The miles on the chassis is 75,000 and the engine has roughly 100 miles on it since it was completely rebuilt. The car is still on a base tune and needs a little bit more easy street driving before I would feel comfortable putting the car on a dyno and finalizing the tune. The car runs and drives great. I have not gotten into much boost to be on the safe side. I always try to be as cautious as possible when breaking in a new engine. I have performed two oil changes on the car so far and still have the oil/filter from the last oil change that a potential buyer is welcome to inspect.
This car has had extensive custom work performed on the engine bay, firewall, front crash bar, and lower radiator support. The engine bay was smoothed (the original panels were not completely cut out as some people do), a custom tubular radiator support was added, and a custom crash bar/intercooler mount was made. This work took a long time to complete as it was not just ordered from somewhere… everything was custom made specifically for THIS car. As far as I can tell, the roof, rear bumper, quarter panels, and trunk are original paint. The rest of the car was repainted or at the very least blended at the time of the engine bay smoothing. The body of the car is perfectly straight, no dents or dings anywhere. The ABS system was deleted and the car has custom tucked brake lines that run in the transmission tunnel instead of everywhere that is visible like factory. It has a Wilwood adjustable proportioning valve to adjust brake bias. The factory hydroboost is retained and all of the lines were converted to AN fittings/hose from Russell (not cheap!). The body harness is tucked completely out of sight and the fuse box is custom mounted in the drivers side inner fenderwell as are the rest of the control modules/relays. The harness has NOT been hacked up and is still completely intact. Horns still function and even the windshield washer wiring is still intact. The inner fenders do indeed still fit in the factory locations. The radiator is tucked to under the radiator support and has custom mounts. The more you look, the more custom things you find that have been modified or hidden as you look around the engine bay.
The engine from bottom to top is setup as follows, all machine work performed by Kevin Mullins of TKM Performance
Teksid block, stock bore
Kellogg Crankshaft, unturned
Carillo I-beam rods
CP pistons
GT500 windage tray
ARP main studs and main cap bolts
King racing rod bearings
Clevite main bearings
HEAVILY ported 9 thread 04 Cobra heads
1mm oversized valves
Ferrea valve springs, guides, keepers, retainers
New OEM lash adjusters
Melling billet gear oil pump
Ford Racing Timing kit
MMR billet passenger side secondary tensioner upgrade
Upgraded 8mm timing guide dowel pins
Crower Stage 3 cams
Cams degreed properly
MLS head gaskets
ARP 2000 head studs
2.76 pulley on stock blower
Kooks longtubes
Kooks x pipe
Polished Borla catback
JLT Intake
Simens Deka 60lb injectors
SCT BA3000 MAF
SCT handheld tuner, base tune done by Carolina Speedworks
Afco heat exchanger
Brand new Bosch IC pump
ON3 coolant crossover delete
SVE aluminum radiator
Transmission:
Stock T56 with Liberty 26 spline input shaft upgrade
SFI approved flywheel
Mcleod RXT twin disc clutch
MGW shifter
Royal purple fluid
Suspension/brakes:
Powerstop slotted/drilled zinc plated rotors
Orange painted calipers
Eibach springs
Wilwood proportioning valve
Maximum Motorsports CC plates
Misc:
SVE Series 2 wheels
Mickey Thompson 305 drag radials
Double din head unit
Battery relocation done as clean as possible
HID headlights and foglights
LED interior and license plate lights
All custom aluminum overflow/reservoir tanks
EGR delete
Rebuilt oil cooler
This isn’t your average 04 Cobra. It will be a focal point of any Mustang meet and draws a ton of attention. The engine was built with making 1000+RWHP in mind and is ready to handle that with a power adder of your choice. The car runs and drives very good as it is, but like I say the tune isn't spot on and it will need a final tune.. I figure whoever buys the car will probably want a bigger blower on it anyways. The only BAD thing that I know of is the car does not have AC. The firewall was smoothed and the holes for the evaporator were deleted. You could put AC back on the car, all wiring is still there and I have some of the components, but you would have to take the dash out to find/ recut the holes and install the evaporator. Heat works great as does the rest of the power options, even cruise control. The pictures speak for themselves as to the condition of the car. The interior is very nice and all of the seats are very nice with the exception of the usual wear on the drivers side bolster. I would rate the engine bay a 9/10 and the exterior of the car a 9/10 as well.
NO LONGER FOR SALE. $30,500. Not looking to trade at the current time. The only reason I'm selling is I enjoy building the cars more than driving them and I've ran out of things to do to this one, lol. Just looking to free up some garage space and money for new projects.
Last edited: