vmp

I am selling a brand new VMP 137 monoblade throttle body. The TB has been never installed as I was acquiring parts in the late summer and early fall for my build. Those build plans have changed significantly, so now I am selling brand new parts. Works with 2015 - 2017 Mustang and F-150 (5.0L)...

Was finally able to take the Mustang out to the local drag strip (Bandimere) after installing the Gen 2R Stage 1 kit last year. I was somewhat disappointed with a fastest time of 12.8. However, this seemed to roughly the around the same speed the stock 13-14 GT500’s were running. This is my...

2015-2017 Mustang GT VMP Gen 2R Supercharger On 91 pump gas with GT500throttle body I made 690whp (to the ground) On E85 with the twin 67mm throttle body, I made 816whp (to the ground) Selling the entire kit as a whole with the GT 500 throttle body. However I upgraded to the the VMP twin 67mm...

SOLD

Okay so about a month ago I took my car in for smog and I am currently running an E85 Tune. Like a lot of people on these forums, long story short I didn't pass. both my Oxygen Senor & Oxygen Sensor Heater read Not Ready. So where does any car enthusiast go when they need car information? The...

To start this conversation, here is my config: vmp gen2r+2.4 pulley, 10% od, id 1000, jlt 123 mm, jba shorty headers, stock throttle body, vmp tune. I have read several forum threads on the same issue but my case is different. My car has intermittently been going into failsafe engine...

Im selling my VMP GEN 3 super charger, and the KB 168 throttle body adapter plate. It fits 07-14 Shelby GT500. It was on my car for less than 1k miles, and 500 of those were motor break in miles. Its practicaly new! Asking for $3100 including shipping!!!

Hi all, I am a bit torn here and haven't found good information on this exact topic yet. I've got a 2010 GT500 with a Stiegemeier ported M122 with a 2.2" pulley, JLT 123 intake, BBK 65 MM throttle body, and VMP inlet elbow. I plan on adding the 13/14 56# injectors and VMP fuel pump boosters...

Purchased September 2019 - Impulse buy which I have now decided not to install. Never opened or tinkered with. Retails for $850.00 on VMP's website. I am asking for $800. You pay shipping.

Hi all, Looking to pick up VMP's Fuel Pump Booster setup for my GT500. The car is already modded and dyno tuned and running 18psi on a ported and 2.2" pullied Eaton. My recent data logs are showing that the fuel pumps are basically maxed out and so I figured going this route would work out...

Looking for a blower upgrade for my 2007 gt500.. Intrested in gen 1 vmp, stock trinity 2.3 blower, Ford racing tvs, also open to reasonably priced gen 2 vmp head units. PayPal ready 361-947-7300 is my number as I hardly check this page. Thanks!

I'm getting ready to install my VMP Stage 1 kit and oil pump gears next weekend. The install instructions seem pretty clear...already printed out. As I wait for my final parts, I had a few initial questions: 1) I bought a timing cover that has already been modified. I want to install the...

Anyone have a 3.6 kenne bell or a vmp gen 3 for sale???? $$$$

Anyone have a 3.6 kenne bell for sale or possibly a vmp gen 3? $$$$

Looking to buy a aftermarket supercharger for my Terminator. Preferably a Whipple but I am open to other superchargers if the price is right. Looking to buy in about a month.

Hey guys how is it going. My name is Bryan and I would like to introduce you guys to FRP. We are located here in Manteca CA, and offer a full range of services for your Shelby/Coyote/4V needs. Whatever you guys may need I’m just a text away at 209-497-3008 or find my work on Instagram @frpauto .

Hello, I have a VMP 100MM MAF Conversion Kit for the Terminator for sale. It is brand new, never used. Included in the kit is: (1) VMP 100mm Slot-Style MAF Housing (1) VMP 3500 Slot-Style MAF Sensor (1) VMP Plug & Play 96-04 to 05+ MAF Sensor Adapter Harness (1) S&B Air Filter As you can see...

Currently in the process of installing my VMP Gen 2R and the EGR tube is being an absolute pain. So I'm just about to order a EGR delete kit and be done with it. My only concern is getting the vacuum lines right for the SIP. I looked at a guide (I believe was posted on here but was for a...

Looking for an upgraded supercharger from stock, open to all makes, models and sizes. I may also consider ported eaton’s, post up what you’re looking to sell! (PayPal ready/cash in hand) located in Long Island, NY.

Looking for an upgraded supercharger from stock, open to any makes, models and sizes. I may also consider ported eaton’s, post up what you’re looking to sell! (PayPal ready/cash in hand) located in Long Island, NY.

I'm getting ready to install a VMP Gen II blower this spring and I need to keep the EGR and the associated "birds nest" on the driver's side of the blower due to emissions requirements. The VMP does not have a bracket to attach the whole mess to the blower like on the stock Eaton. I've seen...

Only items in the list are for sale. All others in images are either sold or still with the car after trade-in. Sold car to move to a GT350. Swapped parts off of it before trading it in. Only what's listed below is for sale, anything else seen in the pics already sold or was traded in with the...

Hi all, I am selling my take off M122 with a Steeda 2.6 pulley and a VMP Inlet Elbow. I recently swapped to a ported M122 setup with a 2.2 pulley and figured that this one would really just sit on the shelf. The blower has about 50,000 miles on it and overall the ribbing on the pulley, the...

I currently have a built 2v motor in a 04 GT with an Eaton m112 blower. Teksid block. Forged internals. Im making around 450hp with the current blower at 12psi. My motor and fuel system were built to handle 700+ hp but I skimped on the blower during the build. I'm looking to upgrade now and...

Hi all, I am selling my take off M122 with a Steeda 2.6 pulley and a VMP Inlet Elbow. I recently swapped to a ported M122 setup with a 2.2 pulley and figured that this one would really just sit on the shelf. The blower has got about 50,000 miles on it and overall the ribbing on the pulley...