supercharger

Hey guys I have for sale a bunch of goodies for 1996-1998 cobra. I have the 2.1 polished big bore supercharger with all the pulleys and hardware included. It has less than 8k miles on it and the rotors look amazing. Also I have a set of b-heads ported by fox lake with 2k miles on them...

Hello Everyone, I am in the middle of a 2009 Mustang GT (4.6L Aluminum Block) build, and I requested some input from Mr. Colletti through a friend. I was informed that John is lying low and wouldn't be available to respond, and that this forum would be a great place to get some feedback...

Kenne bell with behemoth mph inlet. Kb dual tb and matching 4.5" RAI. $3800

"]http:// [/URL]"]http:// [/URL]"]http:// [/URL]"]http:// [/URL]

Hey all, I've always loved and had older Mustangs since I could drive, but I've just recently had the time and money to get some new stuff and be able to modify the car so please forgive me if I ask some dumb questions. I have very little experience when it comes to this but I certainly want to...

Hey all, I've always loved and had older Mustangs since I could drive, but I've just recently had the time and money to get some new stuff and be able to modify the car so please forgive me if I ask some dumb questions. I have very little experience when it comes to this but I certainly want to...

SOLD!!! I'm selling my 98' Cobra, it has a procharger (rebuilt less than 1000 miles ago), 50lb injectors, Aviator fuel pump, cat delete, Bassani exhaust, sct tuner, dyno tuned, 458rwhp 412rwtq, Centerfoce clutch, driveshaft loop, Saleen body kit, 18" Saleen style wheels, S351 style spoiler, new...

SOLD Thanks SVTP

I have a Complete Saleen Blower kit (eaton M90) for and 4.6 2v with p.i. heads. (blower, custom intercooler, saleen coolant tank, heat exchanger with dual fans, water pump, and custom CAI) blower works grean and is direct bolt on. asking 3500.00 OBO. PM me with any questions.

so finally got the blower off and all the internals look good. I am selling because I am getting a 2.8lc. oil was nice and clear, front seal in snout changed and I have a new boost bypass that comes with blower. I am asking $2500 obo plus shipping. I near Bakersfield CA and my number is...

Sold

Sold sold sold sold sold sold sold sold sold sold I have a 1997 Cobra for sale. I hate to sell, but I'm afraid I don't have time to mess with it anymore The car does suffer from a vacuum leak that causes the car to have hanging idle. Other than that car runs like a champ. Odometer stopped...

Engine & chassis has 62,000 original miles on it. The eaton swap was done using parts off of a 30k mile 04 cobra that went turbo. Mods Stock 99 motor with eaton swap Tubular K-member, control arms, & coilovers (front) UPR rear control arms (SRA) Metco lower pulley kit (stock ring) Canton...

hey guys i have recently bought-en an eaton m112 with throttle body and plenum and then came across a deal for a mark 8 motor and bought it. I also have some #39 03 cobra injectors with about 25k miles on them too. dont need eaton now since im going to do a mark 8 swap in my 2002 v6...

Can someone make a list of mods that would be needed for a 2.9 whipple to put under 700rwhp down on an 03-04 cobra ( like what kind of injectors, fuel system, maf, etc. )

I've combed through a lot of forums and decided to run flat top pistons with my centri build; my car is a 97 cobra. I think my compression will be around 10.9:1; what kind of boost would you guys recommend for pump gas? I was thinking about 12 pounds but that may be too much for pump gas I'm not...

Has anyone had luck with getting good numbers on a 2001 stage 3 roush blower m90? Also is there anywhere that I can find new screws for it to be rebuilt? When I bought the car and took it apart the screws have all sorts of scratches and gouges in it and want it to be fixed right... any...

as the title said. i have an 04 lightning that i bought with a whipple blower. I'm trying to sell the truck but i want to keep the whipple blower. Anyone have a factory blower or one that would bolt on for cheap or know where i can get one?

1

OEM Eaton M122 with elbow off my 2011 GT500. Has only ~9000 miles on it. Asking $375 plus shipping.

Looking to sell my Roush supercharger off my 2001 stage 3 roush. Will be a direct bolt on and will sell it with everything i have, lower intake, throttle body, blower etc.. Works for 99-04 2V Gt's. Can send pictures to serious buyers. If serious go ahead and text 361-489-9449 will ship at...

Basically ive been reading about all sorts of blowers and vmp seems to be one of the beast bang for your buck as far as going 2.3l , ive read about a few people having great results but never specifing whats done to their cars or even what fuel there running. anyone would like to share their...

As title states, wtb 2.9 whipple. Whos got one for sell? I also have a 2.6 Kenne Bell, stock eaton and BBK cai for sell/trade.

I Have A Lysholm 3.3L Blower For Sale. Same Size As 3.4L Whipple Just Different Rotors. Lysholm Used To Make Whipple's Cases And It Was The Supercharger That Came Factory On The Ford GT SUPERCAR! The Blower Comes With A 5" Intake, 123Mm Mass Air, 160Mm Throttle Body And Two Pulleys. Capable Of...

What's up guys new to the forum looking to purchase an intake manifold and intercooler for the 2011 gt500 I have. I was hoping somebody would have one around . Txt me at 9154942370 or email [email protected] with what you have.