Hello everyone I've been searching the threads and looking at all sites for the direct fit mishimoto for 03 04 terminators . I'm getting mixed reviews why will it not fit if they state it fits mach1 cars . And on the mishimoto site it says it will fit?? When you go to different shops it says...
Hi everyone i have a 10 inch fr500 rears with 285/35/18 falkens on back of my lowerd cobra with hr race springs with low profile bolt.. i know that nitto run a little narrowere than rest of tires i want to put 305's on who has them on there car do they look small???
IM NOT ROLLING FENDERS CAR...
Im trying to find the size of coolant crossover plug o ring size anyone have .. i want to switch to viton o ring.
Who still makes the plugs .. been long time i bought one and o ring ripped.
Thx
Hey guys im trying to find out on a 18x10 rim with a lowered car with hr race springs with mm irs bolt can i put a 305/35/r18 tire on the rear without rolling fenders..
Pics please.
Thx very much
Hey guys . I'm wondering if any new rads for our cars have come out yet that are direct replacement!?? Mishomoto fluidyne etc have had some before that said they were but weren't so any new models etc??? Or redesigns?
Thx
Back flushing intercooler system? Iat2 at stop light! temp?
Hey everyone just wondering if it's a good idea to back flush I/c system ? Any tips on how to go about this ? I'm suspecting a blockage. Because when car is stopped at a light iat2 goes up quite a bit compared to iat1 recorded on my...
Anyone have bridge bolts torques numbers
Hey guys quick question I need torque values for pulley bridge bolts ! Are they all the same? I want to change inner belt and do some maintanance.
Thx fellas
Changing orings on coolant tubes for supercharger!
Which gaskets can I reuse? And which ones will I have to buy?
To do the job right
think my o rings are leaking
Thx
I'm working on my car because it's put away for winter and have blower off the car now I need some advise on how to heat the bolts with pro pain torch
Do I heat the head of the bolts or the serounding metal around them to
Break the thread locker I don't want to break any !!
Thx
Hi guys need to be schooled. I pressure tested intercooler system
And it held pressure ! For a couple of minutes at 13 psi. And I did the same with cap everything checks out! But have had coolant drop a tad .
It's gottin a little colder out and I'm thinking coolant shrank a little . What do...
It's not a lot 2 mm but I'm concerned! I pressure tested system at 14 psi and nothing it holds pressure! I put new cap on and tested that and all good !
I'm stumped? Weather has gottin colder around. 50 's and dips into high 30's at night could it be the coolant contracting??
Thanks
Al
Hey guy I need to know if ford still makes the undercooler for our cars
I'm concerned about this because the cars are getting older and there really is
No options that I know of? Velocity? Lfp?
And how do we determine with a pressure test if it's the undercooler
Or cross over tubes o...
Hey everyone i know this should be in suspension part but i need some more opinions .
I put powerstop crossdrilled and slotted rotors and evolution ceramic brake pads on all around that was a kit from stage 3 motorsports. they have been great for over 2 years now, i've developed a slight...
power steering level ?
hey guy's i have a question about filling my power steering fluid. the car has power steering fluid at the low level when car is cold and in middle of max and min when hot.
Is my fluid low? do i add to middle while car is cold??
Manual in car doesn't say.
hey guy's my headlights have a film inside not on the outside like most people. i always polish and wax the outside of them and there really clean, but there is a film inside the light and a few fingerprints inside.???? i have new ones but was wondering do you guy's have this to. maybe its when...
Hey guy's wondering if i can put the stock tune back in while i have the 2/76 upper installed just so i can get the monitors to reset for emission test. I will not put her into boost at all I just need to have the monitors go ready.My tuner shut all of them off and i don't want to get car...
new flowmaster highflow catted h-pipe (4 cats)
I just got an e-mail from american muscle about this new h pipe that has 4 high flow cats like the stock h on our cars. anyone use it yet what do you think. For emission tests it should help with visuals but is it worth it.?
hey everyone i have a question about pressure testing my intercooler system. I test to 10 psi and have good pressure for about 3 minutes . my question is if the 0 rings are bad would the pressure drop or will the o-rings be bad only under high boost.????
Hey fellas Quick question how many of u have the stock clamps on your I/c resevoir. I did a pressure test and i have a leak at the bottle nipple of the stock I/c clamp . I've tried positioning it in different spots. I will try a hose clamp thats screw on type. i checked tank and no cracks .
Anyone use these???? and do they work????? there made by jdm engineering U screw them in exhaust bungs then screw 02 sensor in out of the way of gas flow.
Do 02 extender non fouler work???? by jdm engineering the pieces you screw into the midpipe and then screw your o2 into to raise them out of the path of exhaust and if so where can i purchase them????thanks
I just changed i/c pump and it's about37 deg outside pretty cold. i changed the pump and took car for ride, coolant moving in tank but not churning hard. i've done the blowing and sucking on resevoir . I think all air should be out.
Iat1 78 and iat2's are 79 degrees. because it's cold outside...