Hello
I'm willing to install throttle body in 13 Shelby
Which throttle you prefer to gain more RWHP without any drive issue
VMP 67 mm or Ford Racing 65 mm ??
Dynos, numbers .... ?
Thanks all :banana:
Hello guys
For 2005 Mustang GT with full bolts on / cams / intake manifold and NX nitrous system. :burn:
Which plan you suggest :
A. Ported cylinder heads
B. 298 cid stroker kit ?
Also, which brand shall I go for ?? :rockon:
Regards
Hello guys
I'm planning to install 03 Cobra engine and transmission in 1996 Cobra
I found Engine ( From oil pan to throttle ) and alternator , transmission, power steering pump, wiring harness and ECU
What else I need ?
Heat Exchanger , Radiator, Fuel Pumps, Intake, Driveshaft, Fans, FPDM...
Hello guys
For 1996 Cobra , Im thinking to install Crower stage 4 cams
Ford Modular Camshafts
The application is high speed, I need the max NA power and I will put 100 shot in the future
Im worried of the piston/valve clearance, Do I have to cut the stock pistons ?
Any body tried it ...
Hello guys
For 1997 ( 2 V ) Manual trans. I would like to go for cylinder heads and Forged stroker kit
Then, I will spry it 100-125 shot :lol:
I have already Crower Cams stage 4 ( Dur @ .050” Lift: 228°/232° RR: 1.8/1.8 Gross Lift: .612”/.621” LSA: 114 ) and it’s working very fine...
Hi Guys
Looking to replace the fuel pumps for my 09 GT500
Where can I find the fuel pumps it self ?
Or I can install Ford GT fuel pumps directly without any modification
I think that the Walbro will not fit coz it's return system
Why I cannot find any clear website provide fuel pumps...
Hi guys
For 09 Shelby GT500 with upper/lower pulley and bolt on
Is there is any aftermarket clutch to be installed with stock flywheel
Since SPEC/Ram/C.Force required to buy flywheel
Thanks All
Hi guys
I want to buy the most powerful N/A cams for my 96 GT full exhaust , Intake , Pulleys , BBK 78 mm T.Body with plenum, PI ported Heads, PI Intake Manifold
I'm thinking of Crower Stage 4
62805-2 Stage 4
Race grind.
ECU mods and tuning required.
Rough idle is common.
RPM...
Hi guys ?
Is it possible to use Shelby GT500 s/c oil in a 2.6 KB 03 cobra ? Is it the same of KB oil ?
Does the stock GT500 s/c use the same oil of stcok 03 cobra s/c ?
Advices pls.
Thanks,
SVP AM
Hi guys,
I have a brand new bulit motor, brand new cylinder heads,
In breaking in the car was OK
But after 2-3 wot runs I found a tick in the engine in idle only
but if I just press the gas paddle 1000 + rpm the sound is OK
Also, I checked all the spark plugs it was really clean...
Hi guys,
I want to buy a fuel system for a 03 Cobra
Dual FPDM kit
Hat
-8an lines
Fuel Rails
Addaptors
Hope I find a clean lethal Performance fuel system kit
Urgently guys
thanks
I have a 03 Cobra with 2.6 KB, built stroked motor, fuel sys and full exhaust
I swapped the upper KB pulley from 3.25 to 2.75'' ( The smallest pulley in KB )
After I swap the pulley at the same day, s/c oil melt the oil cap and goes out, I thought it's over fill so I replaced the cap and...
Hi All,
I have a 2.6 kb in my car
I just swapped the upper pulley to smallest one 2.75
I also have 4lb lower.
I have a built motor and using race gas
Now, Last night I was driving the car 80-100 mph with out boost ( Zero Boost )
I smelled something like burn from the engine
I...
Hey guys,
I have a tick issue in my current heads
My application is 2.6 Kb , full exhaust , fuel sys
Also, I want to go for twin turbo after a year or something like that.
So what to choose ?
1- Buy stock heads and install aftermarket high lift cams with springs ?
( CompCams...
Hi Guys,
I found a noise in the engine last night
when the car is cool the engine is roughing !
Idler cont is clean, fuel pumps is new, injec are clean, t.b is ok
Also, I feel that there is decrease in power
After 2 runs I heard the noise
it's like ''tick tick'' and it's increases...
Hi guys
I have 2.6 KB with 3.25''/4lb
this combo gave me 20lb of boost only !!!!
I want to go for 2.75/4lb to get more boost
Somebody told me that your engine will hirt !
But I said as long as I did not get 24lb from 3.25/4lb
so I will get 22-23 with this new combo 2.75/4lb
I will...
Hi guys,
I have a 2.6 KB, I installed a auto meter cobalt gauge
With the ''T'' that come with auto meter gauge
My combo is 3.25/4lb with LFP idler 100mm, 79'' Gatorback belt
Boost gauge just give me 19-20 lb of boost
Why ???
Also, I sow many vids the stock boost gauge goes down to...
I found out some cut fuel in my high boost 2.6 KB, 60lb injec, Dual Ford GT pumps ( Stock FPDM ) , Also I will go for N2O (50-125 ) shot
I just replace my pumps and the car run ok, no fuel cut
they told me that the problem was the FPDM I have to buy a modified one coz the stock is pegging...
Hi guys,
I have a 2.6 KB with full exhaust, 3.25 upper, Metco 4lb lower, LFP idler aux pulley
I always have a problem in belt , before it was slipping after I install LFP ilder, no slipping
now, The problem is the boost was not go more than 18-19lb
It should give me 22+lb
Before I...
Hi guys,
I want to spray my 2.6 KB, for sure I will go for race gas
I have full exhust, 20lb of boost
Somebody told me that the spray will damgae the blower !!
even it's 30-50 shot coz it's very cold and entering in a hot roots
So the guy told me to install it in the intake manifold...
03 Cobra with KB 2.6L
3.25'' upper /4lb metco lower combo
Belt number K080797
I have a major boost drop, first of all this combo should give about 20lb+ of boost it gives only 17lb max and drop with higher rpm specially after 5000 rpm and give 9-10 psi only
With higher rpm I go with...
Hi guys,
I installed a 2.6 kb with 2.75'' upper, 4lb lower
60 lb injectors, dual Ford GT fuel pumps
how many lb of boost I will have ?
What is missing in my fuel system ? Is there a risk to the engine with this amount of boost ?
I want to spry the baby let's say 100 shot ? what do...