In 2013 Van sold me a SPEC SS trim stage 2 clutch kit for our GT500, as of today the car has more than 82k miles on it, and the clutch has 61245 miles on it....... yes you read that right over 60k miles. This car is a daily driver, with a mix of stop and go, in town and freeway miles. Only one...
DIRTY, SUMOBITCH, LYING, ASSHOLE previous owner.
My car WAS wrecked......:nonono:
I have seen a few clues over the last few months..., but nothing I could call the guy a dirty POS..on.....
But as I went to replace a leaking right valve cover gasket, I found the timing cover cracked in two...
2007 with 21,300 miles.. and found the left rear caliper rubbing the rotor this morning on the way to work....
Heard it grinding as I pulled into my parking space at work..... sound reflecting off the car next to me was lould....
Pads were fine last week. and the right side .. but looks...
This is install number 2 for the SPEC Super twin SS trim clutch and #3 SPEC clutch install over all in as many months. ( all different cars not re-dos )
It was finally time to install this one as the clutch had started to slip under boost in 6th.
Started at 1830 with pulling on to the...
Out for a day drive, 96deg ambient temps. Stopped for a snack and it over heated blowing coolant. Figured I'd find a holed hose, but no it was. Oil over from the cap and the fan was not running. Fuse is good as are the relays (swapped with other known good one)
So power issue or fan motor dead...
Had a breaking induced front end vibration last few weeks,,, decided it was time to have the rotors turned and some new Hawk HPS pads.
Pulled the rotors this evening,,, damned if I did not find a hub bearing LOOSE, noisy and the grease cap had some water in it. :fm:
Had planned to put a...
This is the part where I discover what a foot tastes like.....:nonono:
As I spoke of MY camber plates not making any noises :dw: and they do not, the MM plates on our 2005 S197 GT make no noise at all in 62,000 miles of use.
So when it came time to order camber plates for our 2007 GT500 I...
My '05 S197 has wheel Hop... the '07 GT500 does not, of course it has more power and no traction... the F1's just spin 1-3.
I know, the OEM F1's are crap...... but as a daily driver I can not run DR...so a compromise tire will need to be found.
And then the suspension..
I'm dealing with...
The aluminium trim pieces that the arrows above point to.. Anyone know if those are replaceable as a service part?
I've looked though Tousley ford on line parts pages and not found them.
The PO of my car dinged those trim pieces in a few spots, nothing bad or structural, but my wife and I...
Ever wounder what went on in that motel room before you stayed in it? :dw:
Why, if it's was I that occupied the room prior, it may very well have been Motel MOD's :banana:
Stuck in El Paso for another week...wanted to add some color in addition to plumbed Bob's Auto Sport oil separator I...
For a 2007 is Air intake temp a valid PID?
If so why would it not read a value in livelink
Rest of my selected PIDs are reading so it's not an overall comms issue with the computer.
Thanks
Anyone familiar with the craft shop on post? Have 2 or 4 post lift available at home? or worst case know a trusted shop where I can drive in, and be under the car with the tech?
Just drove in from Ft Hood, and have a suspension rattle I need to look at. Pretty sure I know what it is, as the...
What do you do when on a road trip and you find yourself in octane hell?
Change to a 91 or 90 tune?
Use octane booster?
Stay out of boost and high load, feather the go fast pedal and take it easy till better fuel can be found?
At home I have 93 at many stations
Finding west Texas has...
Can not read DTC after the Jon Lund Tune was installed.....
Post tune I went to check DTC's, and got P1000 OBD-II Monitor Testing Incomplete.
Tried to clear it, no dice..
Seems to be running ok. Did about 12 start and stops with 60 miles.
Same deal today, P1000.
Need to drive the...
What paint code, brand most closely matches the blue powder coat on GT valve covers?
Love the blue. But think a paint or maybe a gloss finish powder coat will do better on my car then the powder coat finish found on the FFRP covers.
Thanks
MGW and Revan Racing Got first blood on arrived shipments...
My son could not wait till I got home in a few days..... Just had to open the first two box,s....:lol:...that's my boy:banana:
Don't blame him...UPS dude showed up at the house yesterday and asked him if we were starting a...
Ordering a Tuner from VAN, but need the car PCM number.. I'm 7,340 miles away from the car and looking to have my son go find the number.. I did a few searches but nothing came up.. Anyone have a link to a thread that describes out to locatet the PCM and the number? Have a pic of the general...
Looking for a good used 2008 and later M-6312-SVT crankshaft damper.
Have one after your IW 10 or 15% swap? Parting out a motor, or an entire car that was not front end wrecked?
Cash for your paperweight.
Thanks
As they are tape.. is there a paint code for them from the OEM? Or a known matching paint code that can be used?
Have some ideas for accents using the OEM Vista blue color, and want to have my local body man quote me a cost on painted stripes when he does some other work on the car.
Thanks
Looking for a tire to use on a custom wheel... as a spare, for a GT500..
Want to match the Overall Diameter as close as possible.
255/45-18 (Front) 27.04 Overall Diameter
285/40-18 (Rear) 26.98 Overall Diameter
So, I want the absolute skinniest tire I can find to run as a spare, then will...
EDIT: This is JUST the power MODS.... not before, after, or inplace of suspension, brakes, a new shifter and some repair items. Sorry for the less then clear set up.
The base line thought is..Spinning the SC faster without addressing heat seems counterproductive. and Heat will be my biggest...
Eaton H122 Service manual, parts list, suppliers .
Normally most any document you want is available on the internet, but either my GoogleFu is weak this morning, or a service manual, parts list, on line parts suppliers and parts fiche are just not out there and easily locatable.
So, are...
As the title states: looking for a good used take off crank balancer / pulley
M-6312-SVT.
Perhaps someone that has done a lower overdrive pulley from IW, or has a takeout motor, core motor.
Cash for your paperweight. :pepper:
PM here, or email [email protected]
Thanks
Trying to confirm some things:
M122 Pulley shaft size where the pulley is press fit.7815?
The pulley shaft is drilled and tapped I think.. anyone now what size / TPI that hole is?
and
Amount (length) of the pulley shaft that engages the pulley?
Thanks
OK so I got wind of an issues with the OEM 2007 damper (car was built late 2006) … Other then the shear mass of it, and replacing it for that reason alone. I’ve not found much.. no crank failures related to this item, broken crank snouts, sheared woodruff keys, vibrating loose… and the like...