just stumbled upon this thread. we mostly were posting on facebook. lol. the car has a base model HP kit with a P1X upgrade. 9.5 PSI. has stock exhaust with just cat deletes. we are using as much of the DI side as possible and blending in the PI side as needed. the converter is killing us for...
Posting up a extra pump hat I have maying around. this is a Gen 1 Fore dual pump hat. even though its older it has less than 5000 miles on it. it works perfect. there is zero wrong with it. the only reason it was pulled out is the new 465 pumps will not fit in it.
comes with everything...
slightly used top of the line alkycontrol kit. This can can be set up to be used on anything but it's currently set up to be used on a 99-04 new edge car. you can mount the tank anywhere want. Julio (alkycontrol owner) can make you a longer feed line. It comes with everything needed to install...
been a long road but it ALIVE!!!!
figured I would share some progress pics....
brief run down:
L&M modded block
manley rods
11:1 diamond pistons
Ported JPC heads
Custom cams
Boss 302 intake
modded phasers
A1000 pump with 20V BAP
ID1300's (might be doing 2000s soon lol)
FTI...
this particular blower came off our 3 valve car. it litteraly has about 500 miles on it. we put it on. tuned it. made 700 wheel on pump gas. and 500 miles later i lost a follower in the motor so we pulled everything down and i happened to get a good deal on a F1C so this f1a is up for grabs. :)...
this particular blower came off our 3 valve car. it litteraly has about 500 miles on it. we put it on. tuned it. made 700 wheel on pump gas. and 500 miles later i lost a follower in the motor so we pulled everything down and i happened to get a good deal on a F1C so this f1a is up for grabs. :)...
selling this clutch we had in our car with a magnum. has 600 miles in it plus 5 passes...
this is the stage two rated at 1100 ftlbs.
retails for $1,600 will sell for $1000
shown in the picture is extra disks for when we had it behind a mt-82
text is by far the best way to reach me...
This came out of our shop car. the car had a procharger on it. we did the spec twin disk for the mt82 part number SF50SST-2 rated at 1000 ftlbs. we ended up breaking the mt82 and swapped to the magnum xl. we had spec send us the 26 spline disks which are stage 2 disks. rated at 1100 ftlbs. the...
Hey guys. Just finished a TH400 swap and now selling the six speed stuff off
includes everything pictured or will part out.
can arrange shipping if need be.
trans has 70K on it and is completly stock. shifts perfect. came out of a pulley only car. pulled it to do turbo/auto build...
hey guys,
posting this blower I have up for sale. Was removed from a 2014 GT500 with 5,900 miles to install a kenne bell.
included is the almost brand new blower with a Billet Pro Shop 2.396 pulley and the plenum.
$2,000 shipped to your door in all its silvery goodness. Or best offer of...
just finished Modmike1572's car. there was a lot of speculation on rather or not the stock tb is a restriction or not and now we have solid data. IT IS..:-D
mods are:
vmp tvs
2.8 upper
aux idler
stock lower
stock manifolds
OR-X pipe
bassani CB
jlt fenderwell coild air intake
Accufab...
Thought i would share . Maybe get svtp on this shit too... its just starting to get good
Scam Alert!!! Mobile Truck Repair 855-400-0855 - Yellow Bullet Forums
i bought these from latemodle restoration for swapping a coyote motor into my fox. we bolted them up to the engine then went to install the 4r70 and they wont clear.
i had to buy the kooks ones. latemodel wont let me return them because i threw the box away. so im selling them. these are the...