Well I maned up and did it...

[GodStang]

Well I manned up and did it...

I could not decide what injectors to go with being worried that the size would not be big enough. So I manned up and bought a set of ID2000 (~190lbs) from Posi Performance. They should be able to handle any of my future plans!

*EDIT Below*


Well most of you know I kept bothering everyone with questions about what injector to go with. Should I buy the 105s or try and make the power with my 80s or spend a little more for the ID1000s which were too expensive. Well ya I made the decision and called up Posi Performance and ordered a set of injectors. Since I have a Kenne Bell this was my first time dealing with Posi. He was very nice and communication was unreal. I will for sure deal with Posi Performance again.

and now to what the thread is about:

 

[Ironhand]

Very nice Josh. What is 2000cc in lbs? Also, you should post a pic. :thumbsup:

 

[dlaude]

Sweet! Hey, seeing your sig reminds me again, do you have any other vids of your crower cams in action?

 

[GodStang]

Very nice Josh. What is 2000cc in lbs? Also, you should post a pic. :thumbsup:

I do not have pics yet since I only ordered them. I was going to wait till I got them before posting this but I was too excited since I have been seriously been stressing about what injectors. I think they are ~190lb injectors.

Sweet! Hey, seeing your sig reminds me again, do you have any other vids of your crower cams in action?

Got tons of them. Give me a few and I will find them.

 

[GodStang]

My cams. Most are the 2.2L:

[ame="http://videos.streetfire.net/video/03-cobra-walk-around302vt-stroker-22l-kb-cam_28913.htm"]03 Cobra walk around.
302VT Stroker, 2.2L KB, Cam - Car Videos on StreetFire[/ame]

[ame="http://videos.streetfire.net/video/walk-around-tick-2_151576.htm"]Walk around Tick 2 - Car Videos on StreetFire[/ame]

[ame="http://videos.streetfire.net/video/lifter-tick-1_151572.htm"]Lifter Tick 1 - Car Videos on StreetFire[/ame]

[ame="http://videos.streetfire.net/video/2003-kb-cobra-on-the-dyno_111720.htm"]2003 KB Cobra on the Dyno - Car Videos on StreetFire[/ame]

 

[SSeatr]

nice!!! im leaning towards this way too, just money is what i am waiting on.

what did they run you?

also the ID2000 arent they 2200cc?

 

[dlaude]

Awesome, thanks a ton!

My cams. Most are the 2.2L:

03 Cobra walk around.
302VT Stroker, 2.2L KB, Cam - Car Videos on StreetFire

Walk around Tick 2 - Car Videos on StreetFire

Lifter Tick 1 - Car Videos on StreetFire

2003 KB Cobra on the Dyno - Car Videos on StreetFire

 

[gt347mustang]

Car sound good!

Was that noise from a faulty lash adjuster?

 

[GodStang]

Car sound good!

Was that noise from a faulty lash adjuster?

Ya we replaced the whole passenger side and the noise went away. I am in the middle of completely redoing the exhaust so we will see if she will sound better.

Here is some info on the injectors:
Nominal Flow Rate - 2225cc/min @ 3.00 Bar (43.5 psi) Using Gasoline at 52 Degrees C (125 Degrees F)
Maximum Differential Fuel Pressure - 9.0 Bar (130.5 psi)
Fuel Compatibility - Compatible with Methanol/Ethanol/All Known Hydrocarbon Fuels. Incompatible with MTBE/Nitro Methane/Nitro Propane.
Electrical Connector - Denso

 

[04cobrawhine]

price?

 

[GodStang]

MSRP is $259.95...and injector.

 

[04cobrawhine]

ouch...

 

[GodStang]

Now with pics