Search results

Had car dynoed the power curve is very choppy, car runs fine and isn't down on power. I replaced plugs and coils which made problem better but not fixed. Leak down and compression test are good also scoped cylinders everything mechanically looks good. A/f and boost is also where it should be.

Wondering if this is the supercharger gears, bad pulley, valve train noise or something else? Thanks for any input https://vimeo.com/134580919

anyone using anything different than the motorcraft synthetic 5w50 oil in the 13-14's? :??:

Which are the best all around brake pads for low dust, no noise, and great stopping power?

does anyone know the ford part# for the crank pulse wheel? Thanks

I installed a new clutch and no engine lights I decided to to a cam relearn for precautions I did it with the ford Ids it stopped half way through and now have p0315 engine light on. Can't get the car to relearn with the Ids or the x4. Car has 10% overdrive, scj mono, JLT intake Lund tune, full...

Anyone running weld rts on front and rear with track package, I know I can change rear brakes and all that. I am looking for size (assuming a 17 or 18 rts) offset and if anyone has experience with them on a 13-14 track pack car? As always thank you for your help

Darryl is off all week so I am dealing with Stephanie at Ace, I need a clutch for the car and being in Michigan there are very few days that its nice out so I would like to drive the car as soon as I can get a clutch in. My question is to the guys running the twin powercore clutch can you really...

Mods are 13-6 kit. When I don't lift shifting leaving it to the floor or quickly coming off gas then back in the rpms stay up and don't drop down for about 2-4 seconds. Is this clutch protection or a going bad clutch? Also in 5th gear at about 2k rpms rolling into the throttle the rpms raise...

does anyone know if you need specific 2013-2014 gt500 coolant and intercooler expansion tanks or if the 11+ tanks work?

what is everyone running for aftermarket clutch? ease of install? any help is appreciated! Thanks Mike

I installed the bobs passenger side no problem, now working on the drivers side trying to figure hose routing that looks clean and that doesn't interfere with anything. Anyone have insight to this? Thanks

Which size is everyone running? Thanks

Just put a set of new tires on. Something a little taller and more sticky on the rear and that hopefully will wear better than the stock goodyears on the front.

If you had to pick which would it be and why?

just purchased a set of 1400 lumens diode dynamics fog lights for the Shelby and they will not seat properly in the housing they keep popping out. anyone else have this issue?

I am considering going to long tubes, I've heard that there is no bung for the o2 and you lose function of the wideband in the car? anyone confirm this?

Ive been looking at doing the corsa catback exhaust but it looks like a axle back setup with an x-pipe? also any benefit other than more noise with removing the resonators?

Has anyone used any of the trucarbon, seibon carbon fiber replacement parts? Looking at the replacement upper and lower grille, and the heat extractor. Looking for fit and finish feedback to anyone that has used. thanks for any help Mike-

I have a set of 20x8.5 KMC GTX wheels and nitto 555 tires for sale tires have 200 miles on them (bought for a lot car never used them other than to display on used vehicle) I think 1200 obo was a fair price

Like title says 79-93 front ride tech air suspension front struts Thank you

I recently did a supercharger on brand new (800 miles) 6.2 Harley truck I have lower intake, fuel rails, throttle body, stock intake ect. I'm open to offers Thanks Mile @ VCW

Chromed HRE 593RS for sale 18x9 fronts & 20x9.5 rears they have nitto 555 tires all the way around. These were professionally chrome dipped and wheels & tires have less than 350 miles on them no burn outs, no issues, and no blemishes or imperfections. 8k obo Thank you

anyone running dumps on their car and covering the exhaust holes on the bumper any ideas on how to make these look better more fitting? :shrug: thanks for help:pepper:

sorry if this is a re-post i was wondering who makes the lowest shifter handle, meaning in height. thanks!