Not just Alabama also NJ legal age of consent is 16. It only becomes a crime if you are in a position of authority over the 16 year old ie their school teacher, boss at work, parent or guardian. Here is the statute.
2C:14-2. Sexual assault.
The victim is at least 16 but less than 18 years...
Well I had a draw on my battery I finally chased it down to the passenger side rear amp. My system is 100% stock. The right amp was drawing .18 miliamps and was killing the battery. So I unhooked the amp and the draw is gone. So here is my ? When I disconnected the right amp there was no...
Ok I replaced the original oem battery 3 weeks ago because car was dead and figured it was time. Drove the car to my parents and back home about 300 miles. Then parked it for 3 weeks and the battery is dead again. I did an amp draw and it was pulling just under 2 amps. Started with the usual...
I have a SLP pulley remover/installer tool purchased from Lethal performance for sale. Used twice once to remove then once to install a pulley. I don't need it so I am selling it Lethal sells them for 150.00 + shipping. I want 110.00 shipped OBO.
I have a stock eaton with 9,000 miles on it. It currently has a 2.76 pulley on that will go with the blower unless you want it removed and a 2.93 pulley. $350.00 + shipping
I also have a stock elbow for sale 50.00 shipped OBO.
I am selling my CT-R wheels they are in mint shape normal wear no pealing chrome etc. Car is garage kept not driven in the snow or during winter. The wheels have maybe 7500 miles on them tops. They are still on the car selling for 600.00 tires not included unless you want the rears they have...
So the above code is for bank 1 running rich I just did a ported blower with all the fuel upgrades. This is while cruising it happened once I cleared the code a few days later it came back. I thought it may be in the tune but the code is intermittent I am thinking the o2 sensor is going out...
I have as stated above a 2.80 pulley only about 3000 miles on her. I bought a ported S/C and it already had one on. 60.00 shipped this is the pulley and hub. These cost over 100.00 at LFP with shipping.
My eaton is leaking a little from the snout right behind the pulley. I bought the seal but have no idea how to remove the seal. There is a spring clip then the seal how do I remove the spring clip and get the seal out.
Stock parts:42# injectors, mass air, pumps, fpdm w/harness
All parts have 25,000 miles on them
42# injectors-100.00 shipped
stock mass air flow-sold
stock pumps-50.00 shipped never had a bap on.
stock fuel pump driver module with harness-sold
Feel free to make offers.
Stock parts:42# injectors, mass air, pumps, fpdm w/harness
All parts 100% working condition also have 25,000 miles on them
42# injectors-100.00 shipped
stock mass air flow-sold
stock pumps-50.00 shipped never had a bap on.
stock fuel pump driver module with harness-sold
stock mid pipe with...
I am thinking of going coil over in the front I do not want to change the struts. So what would you recommend for the spring rate I want it stiffer than stock I have H&R race springs now. Also the MMR is half the price but I hear you have to mod some oem stuff for it to fit. If you had to do...
Next week I will have my LC-1 I am very good with mechanical work, wiring well I am pretty much a :loser: . Can someone take me through what wires go where and what power source do you recommend me tapping into and how to tap into it. I have heard that if the grounds are not right or if the LC1...
My buddy here at work is selling his bike he bought it to ride with his son but now his son is to busy with baseball and doesn't want to ride anymore (if you can believe that) he is a sports nut. He rode the 450 4 times for a total of about 15 hrs. and the 80 only has about 10 hrs on it. His...
I have seen a lot of how to in regards to changing springs this is how I did it.
The whole install including clean up and test drive to me 3 hrs.
Front Springs:
1. remove wheels then place jack under bottom A arm and compress the spring a few inches.
2. Take off the strut and remove the ABS...
Pair of Ported Edelbrock Performer Cylinder Heads for a 1987 - 1993 5.0
Mustang LX/GT. Upgrades include Crane Cams 1.7 Roller Rockers and Comp Cam
Springs. I also have brand new gaskets and hardened push rods, so all you
need to buy is head bolts. I bought them from a private seller a year...
Ok I changed my wheel set up here it is H&R race springs no isos 18x9/18x10 CT-R Chrome GT-40 replicas Kuhmo MX 275/35/18 and 295/35/18 with a 3/8th in LFP spacer and ET lugs and ground down IRS bolt. The spacer was not needed but I had it from my 17x10.5 with 315's so I put it on with this...