So there is this SUV that I have now had multiple encounters with on my way home from work. They will pull up next to me and maintain my speed or pull in front of me and slow down. I got to the point where I called my local sheriff's dept tonight to report their behavior before this escalates...
I reached out to Ford regarding the purchase of a factory ESP as my current one is about to expire. I have a few questions that I am hoping to receive some input back from the experts here at SVTP. The truck was purchased new and is as follows:
2019 F250 Platinum (almost every option)
6.7 PSD...
So excited for the new season! Reed's back on Yamaha, Stewart's back from suspension and I'm stuck with this cast. Had a small incident back in October in which I tore a ligament and had a bone rotate in the wrist. Not sure I'll even be able to ride this year, much less get full movement of my...
Just got a BDS Suspension 4" lift and 35" Nitto Mud Grapplers installed on the F350. Couldn't let the truck get all the attention so what the hell, pulled out the Cobra too. Rides great with the Fox Racing Shox but the wife (8 months pregnant) is not a fan of climbing into it.
I just had a set of JBA mid length headers installed on my car and should be picking it up tomorrow. I will then need to get it to my performance shop to have the tune checked out. The shop is about 40 miles from my house and if possible I would rather drive the car there than have it trailered...
Spring is almost here and its time for the annual upgrade. I will either be adding a set of cams or headers. Looking for the experts here to share their suggestions on what would yield the best results versus cost / ease of install. (Either way I will have my shop do the install/tune) I have...
Spring is almost here and its time for the annual upgrade. This year I want to either add a set of cams or headers. Looking to the experts here for suggestions as far as what will yield the best results versus cost and ease of installation. (In both cases I will have my shop do the install/tune)...
I finally convinced the wife to let me get a Whipple this spring. I have heard there might be a new 2.9L in the works for the 03/04 Cobra. I think the 3.4L might be overkill (plus there is the clearance issue). I would hate to get the 2.3L only to have a newer unit come out shortly thereafter...
I am looking into getting an X pipe with cats but am open to suggestions as to which one is better, an X or an H. Also, where would be a good place to buy one? This would be for my 03 that already has the Borla Stinger cat back. Thanks.
I just ordered some BFG 315/30/18 drag radials which will go on my 10.5 wheels. I want to move the wheels out and was looking at getting the Maximum Motorsports 25mm wheel spacers with built in studs. My concern is if they will come in contact with the fender lip if they bottom out. Any...
Just finished installing new LFP intercooler and Canton radiator overflow tanks. I filled the Canton up and let it idle in the driveway for a few minutes followed by a short drive to bring it up to temp. I pulled back in the driveway and the stock temp gauge was right in the middle where it...
Just finished installing Canton part#80-232 coolant expansion tank for the radiator. Once installed, I backed the car into the driveway to check for leaks. The fitting right behind the radiator cap began to expel a large amount of coolant and continued to do so until I shut the engine off. Is...
Looks like the first one is going on sale at the upcoming Barrett Jackson auction. Any bidders?
http://www.barrett-jackson.com/events/scottsdale/vehicles/cardetail_list.asp?id=183765
Here is the link to the old post I had earlier this year when the car was getting the paint work done:
http://www.svtperformance.com/forums/showthread.php?t=193500
Here are a few shots I took over the summer that show them off a little in the sunlight. They are very difficult to photograph...
I'm looking to get a set of Lunar gauges (a/f, fuel pressure, boost) for my car within the next few days. Anyone have any suggestions on who has the best deal on these? Thanks in advance.
The Midwest Street Machine Association would like to announce we will be having a car show (no trophies) in collaboration with the Kenosha Airport on Saturday, July 23, 2005. The show will start at 9:00 AM and last until 5:00 PM. There will be free admission and parking for all show vehicles and...
This guy is pretty nuts. I don't even come close to this distance on my full size bike. I'm guessing he's running an over-sized engine kit.
http://www.kylecoen.com/html/video.html
Anyone else have one on their Terminator? I just found out last night they made one so I ordered one up. Any comments? Power increase? Issues? Will be here on Friday, just in time for another car show this weekend.
Took some pics of the car tonight. It will be ready for pick-up on Friday afternoon. The first pic is with flash and the second is with the brightness turned way down and the contrast up in order to see the flames better. The fluorescent shop lights did not work too well for the pics. The flames...