Recent content by SVPAM

Hello I'm willing to install throttle body in 13 Shelby Which throttle you prefer to gain more RWHP without any drive issue VMP 67 mm or Ford Racing 65 mm ?? Dynos, numbers .... ? Thanks all :banana:

Hello guys For 2005 Mustang GT with full bolts on / cams / intake manifold and NX nitrous system. :burn: Which plan you suggest : A. Ported cylinder heads B. 298 cid stroker kit ? Also, which brand shall I go for ?? :rockon: Regards

Hello guys I'm planning to install 03 Cobra engine and transmission in 1996 Cobra I found Engine ( From oil pan to throttle ) and alternator , transmission, power steering pump, wiring harness and ECU What else I need ? Heat Exchanger , Radiator, Fuel Pumps, Intake, Driveshaft, Fans, FPDM...

Hello guys For 1996 Cobra , Im thinking to install Crower stage 4 cams Ford Modular Camshafts The application is high speed, I need the max NA power and I will put 100 shot in the future Im worried of the piston/valve clearance, Do I have to cut the stock pistons ? Any body tried it ...

Hello guys For 1997 ( 2 V ) Manual trans. I would like to go for cylinder heads and Forged stroker kit Then, I will spry it 100-125 shot :lol: I have already Crower Cams stage 4 ( Dur @ .050” Lift: 228°/232° RR: 1.8/1.8 Gross Lift: .612”/.621” LSA: 114 ) and it’s working very fine...

Hi Guys Looking to replace the fuel pumps for my 09 GT500 Where can I find the fuel pumps it self ? Or I can install Ford GT fuel pumps directly without any modification I think that the Walbro will not fit coz it's return system Why I cannot find any clear website provide fuel pumps...

Hi guys For 09 Shelby GT500 with upper/lower pulley and bolt on Is there is any aftermarket clutch to be installed with stock flywheel Since SPEC/Ram/C.Force required to buy flywheel Thanks All

Hi guys I want to buy the most powerful N/A cams for my 96 GT full exhaust , Intake , Pulleys , BBK 78 mm T.Body with plenum, PI ported Heads, PI Intake Manifold I'm thinking of Crower Stage 4 62805-2 Stage 4 Race grind. ECU mods and tuning required. Rough idle is common. RPM...

Hi guys ? Is it possible to use Shelby GT500 s/c oil in a 2.6 KB 03 cobra ? Is it the same of KB oil ? Does the stock GT500 s/c use the same oil of stcok 03 cobra s/c ? Advices pls. Thanks, SVP AM

Hi guys, I have a brand new bulit motor, brand new cylinder heads, In breaking in the car was OK But after 2-3 wot runs I found a tick in the engine in idle only but if I just press the gas paddle 1000 + rpm the sound is OK Also, I checked all the spark plugs it was really clean...

Hi guys, I want to buy a fuel system for a 03 Cobra Dual FPDM kit Hat -8an lines Fuel Rails Addaptors Hope I find a clean lethal Performance fuel system kit Urgently guys thanks

I have a 03 Cobra with 2.6 KB, built stroked motor, fuel sys and full exhaust I swapped the upper KB pulley from 3.25 to 2.75'' ( The smallest pulley in KB ) After I swap the pulley at the same day, s/c oil melt the oil cap and goes out, I thought it's over fill so I replaced the cap and...

Hi All, I have a 2.6 kb in my car I just swapped the upper pulley to smallest one 2.75 I also have 4lb lower. I have a built motor and using race gas Now, Last night I was driving the car 80-100 mph with out boost ( Zero Boost ) I smelled something like burn from the engine I...

Hey guys, I have a tick issue in my current heads My application is 2.6 Kb , full exhaust , fuel sys Also, I want to go for twin turbo after a year or something like that. So what to choose ? 1- Buy stock heads and install aftermarket high lift cams with springs ? ( CompCams...

Hi Guys, I found a noise in the engine last night when the car is cool the engine is roughing ! Idler cont is clean, fuel pumps is new, injec are clean, t.b is ok Also, I feel that there is decrease in power After 2 runs I heard the noise it's like ''tick tick'' and it's increases...