Up for sale is a Dyno Tune Dry Nitrous System. Has a 10lb bottle with high-flow valve and stainless brackets, dump-tube, NOS brand pressure gauge, automatic bottle heater kit w/pressure switch and relay, purge kit added on, micro throttle switch, braided lines and nozzle. I took this kit as...
I'm running Comp Stg 3 blower cams with the idle set around 850rpm's. Tuning with the PRP software on 93 octane. SCT2400 meter, 60's, triple returnless pumps. Motor is a 304ci 4V with race ported heads, Kooks LT's. About 9.3:1 CR. Vortech T-Trim at 10psi until I get a handle on the tuning...
Cleaning out some more spare parts and came across these gem's. I take Paypal Gift, +3% for Goods / Services, or USPS Money Orders. I ship USPS Priority Mail. If you want insurance over $50 dollars it will cost a few bucks more. Post or PM to contact me.
Reichard Racing Manual Belt Tensioner...
Used in great condition Billetflow single-blade throttle body. No corrosion anywhere. Machined finish. No gasket included. Engraved "Terminator" across the top. No TPS, yours will bolt right on. I picked it up used on a complete blower package but never used it on my setup. Asking $350.00 +...
3.25"and 3.5" Kenne Bell Blower Pulleys
Up for sale are 3 pulleys from my Kenne Bell 2.8 blower. The 3.0 and 3.5 pulleys are sold!
The 3.25 was bolted on for one dyno pull and taken off. Asking 50.00 Each + Shipping. Paypal +3% or USPS money order only.
Used in great condition. 1,500 miles of use. Put down 775whp with this and was nowhere near pegged. I'd prefer to sell it all as a kit but will separate if needed. Asking prices: JLT housing SOLD. GT500 MAF SOLD. MAFia Adapter 125.00 + Shipping. Paypal +3% or USPS Money Order only.
Start N' Charge 180 Amp Alternator with wiring upgrade.
Used Start N' Charge 180 amp alternator in great condition. Has over-sized pulley installed to slow it down. Less than 500 street miles with a stock size crank pulley. Never over-spun. Includes 4-AWG wiring upgrade with 250A Inline fuse...
Used Billetflow snub idler 4 pulley kit in very good condition. 3-100mm pulleys and 1- 92mm pulley. Anodized black. All bearings are tight and noise-free. Does NOT include idler relocation bracket. I have the entire Metco lower kit for sale in a separate post. Asking 200.00 + shipping. Paypal...
Metco lower pulley kit with idler relocation. In very good condition. Has a 6psi 9.1" ring. The upper idler bracket bolt is MIA. It stripped and had to be drilled. Same issue the last time I removed it too... I assume its a common issue because Metco sells a replacement bolt kit for 11 bucks...
I have for sale a lightly used TKO 600 Transmission. .68 5th gear. Transmission has Under 5,000 miles of use on it. Bought it from a friend locally to use but ended up going all out with a T56 Magnum. No bell housing included, tho I do have a Lakewood SFI Bell housing for 4.6 Mod motors if...
I have for sale a lightly used TKO 600 Transmission. .68 5th gear. Transmission has Under 5,000 miles of use on it. Bought it from a friend locally to use but ended up going all out with a T56 Magnum. No bell housing included, tho I do have a Lakewood SFI Bell housing for 4.6 Mod motors if...
For Sale: Pair of 28x11.5x15 Mickey Thompson ET Drags. They have been treated in VHT and have just one pass on them. No screws in the beads and zero street miles. Paid 507 for these brand new from Speed Unlimited. I'd like to get 400 for them but make me an offer and we can work a deal. Thanks...
Pair (2) of 28x11.5x15 Mickey Thompson ET Drags. They have been treated in VHT and have just one pass on them. No screws in the beads and zero street miles. Asking 400 or best offer.
Thanks guys!
Tony P.
The parts breakdown calls this fitting a 3/8" Male NPT to 1/2" inverted flare fitting. My Moroso oil pan has a 1/2" NPT bung on the front. My searches have come up short in locating this fitting. Does anyone know where to source a 1/2" Male NPT to 1/2" Inverted Flare Fitting? Thanks for the help...