Recent content by dustin

This is one of the only 4 65special Alternators for a 2003/2004 Ford Mustang Cobra SVT. I bought it and never installed it on my Cobra because it was wrecked. This could be argued as the best alternator made for a 2003 Cobra right now. SOLD! This is a hand-manufactured, all new parts...

I have a used SCT XCAL2 that has been unlocked through LiveLoad: SOLD SCT BA-2400 MAF. Worked great with my 03 Cobra: $180 shipped (price reduced) PLX Devices SM-AFR, SM-100 combo. I have added the cable that hooks up to an XCAL 2 to datalog the A/F ratio. SOLD JLT Oil...

I have a used SCT XCAL2 that has been unlocked through LiveLoad: SOLD PLX Devices SM-AFR, SM-100 combo. I have added the cable that hooks up to an XCAL 2 to datalog the A/F ratio. It worked great with the XCAL2 SOLD JLT Oil Separators and Andair checkvalve SOLD

I have a used SCT XCAL2 that has been unlocked through LiveLoad: SOLD PLX Devices SM-AFR, SM-100 combo. I have added the cable that hooks up to an XCAL 2 to datalog the A/F ratio. SOLD JLT Oil Separators and Andair checkvalve SOLD money order or checks only, no paypal.

I have a used SCT XCAL2 that has been unlocked through LiveLoad: SOLD

JLT Oil Separators and an Andair checkvalve. SOLD Never used McLeod Throw Out Bearing Retainer Sleeve for our T-56. Slight rust since it has sat on the shelf for 2 years.: $60 shipped STILL AVAILABLE and just as good as the Lethal Performance one.

JLT Budget RAI: $50 shipped: http://jlttruecoldair.com/zencart/index.php?main_page=product_info&cPath=1_7_19&products_id=5 Spare Fuel Rail Pressure Sensor: SOLD

Lightning 2.93" upper pulley plus used Gates belt: SOLD Billetflow IRS Brace: SOLD Billetflow Pulley Puller: SOLD

Slightly Used SCT BA 2400: Worked great with my Cobra: $180 + shipped (price reduced) Used Billetflow IRS Brace: SOLD New in box Billetflow IRS Brackets: SOLD Used PLX Devices Wide Band Setup+connecting cable to XCAL2+Autometer steering column gague pod: the SM-100 and SM-AFR combo...

If you have installed MM c/c plates, you have probably already discovered that you can't run the stock dust boots with the plates. Make sure you buy the smaller blue Bilstein dust boots (MM stocks these). My passenger side factory Ford strut has just FAILED because I did not run dust boots...

I'm giving away my stock factory H-pipe from my 03 Cobra. There is nothing wrong with it. I am running a bassani X-pipe on my car right now. The H-pipe has 20,000 miles on it. Local pick up only. I will dispose of it in about 1 month if nobody wants it.

The best front suspension modification that I have done to date. The rubber bushings are extremely flexible. The rubber bushing flex equals to the "loose" feeling you have in your steering wheel. I replaced mine with MM aluminum rack bushings last night. This should have been the first...

Apparently (I have no idea how), I have a small hole in the CV boot on 1 of my half shafts near where the boot is "banded" to the shaft. A little grease has came out but not a lot. Question #1, I do have the ESP on my car. Do you think Ford will fix it? Or say it was somehow my fault...

I'm getting a stainless steel X-pipe soon and I'm wanting to add some stainless steel O2 sensor bungs to it so I can hook up a wide band O2 sensor. Are there any manufacturers or vendors that sell SS bungs? Am I stuck with only regular steel bungs? I prefer to not have a regular...

Here is the story: I have the leaking rear diff, Ford re-seals it under warranty. I then notice a vibration around 35 to 45 mph from the rear diff. Ford changes the ring and pinion. I then install a B-flow IRS brace before Ford works on it. I get the car back, now I have a hideous...