Twin turbo 03 cobra
I am posting for a friend. He has a Black 03 cobra with the HPP racing Twin turbo kit installed. The body has has less than 25k on it other than that everything else has less than 6k on it.The car has working A/C and heat. So far the car has made 800hp on low boost(20psi) and pump gas. We have not had it back on the dyno for the Hi boost or nitrous tunes. the car will make over 1000HP on the turbos alone. The nitrous is only there for getting the car off the line and has never been used. This car is a blast to drive and will roast the tires at any given time. Im sure im leaving some stuff out. Asking $33,000. You can call me Allen at (903) 748-4809 Or Beau (the owner) (903) 824-2878. Mods are as follows
-Turbo Kit-
-Kit has less than 1500 miles on it
-Hpp twin turbo kit with the following up grades
-62mm billet wheel Ball bearing turbos
-Sullivan Lower Intake with HPP Sheet Metal Upper Intake
-Sullivan Fuel Rails
-New Ford 80Lb injectors(good to over 1000hp)
-Turbosmart EBoost II
-Turbosmart Blow Off Valve
-Uni rev 2 step(not yet installed)
-Hpp K-member and A-arms
-Polished Hot and Cold side piping
--------------------------------
-Nitrous-
-Nitrous Outlet 4 solenoid direct port with soft line upgrade(jetted for 150hp)
-Kit is good to over a 500 shot
-Nitrous Outlet Dual bottle Bracket with dual Nitrous Outlet 10lb black bottles
--------------------------------
-Engine Mods-
-motor has less than 1500 miles on it
-Aluminum race preped block .020 over
-Arp head and main
-Probe pistons
-Stock crank and rods
-New Clevite Rod and Main Bearings
-New oil pump
-New Comp hi lift springs
-Hpp Custom turbo cams(intake and exhaust)
-All new valves
-3 angle Race valve job
-New ford gaskets
--------------------------------
-Fuel System-
-Weldon 2345 race pump(good to 2400hp)
-Weldon A2040 Regulator
-Weldon 10 and 100 micron Filters
-Weldon 14000 Fuel Pump Controller
-16 gallon trunk mounted fuel cell
- -12 braided line from tank to pump. -10 braided line from pump to fuel rails. -6 braided Return.
-------------------------------------------
-Rear End-
-Built Straight axle
-Moser 33 spline axles
-Moser full spool
-Moser C-clip elims
-Kenne Bell rear end Girdle
-New bearings
-Richmond 4.10 gears currently installed
-New FMS 3.55 gears(not installed)
-Double adjustable uppers and lowers
-Coilovers on all four corners
--------------------------------------
-Tranny-
-Tranny Is a Viper spec Built by D&D
-Ram twin disc clutch with 900 series disc
-Aluminum Driveshaft
-Pro 5.0 shifter
-Ram billet flywheel
--------------------------------------
-Misc-
-All Vacuum Lines are stainless steel braided line with black fittings
-All Fuel lines are stainless steel braided line with black fittings
-Wheels are black FR500's with polished lip
-Tires are in good shape
-Cobra R hood
-V-6 rear bumper
-Fog lights removed
-Corbeau A4 front seats
-Rear seats are installed
-Bullet mufflers with exhaust dumped before axle
-Tuned at Hpp Racing with sct chip(flip chip is installed for easy tune change on the fly)
I am posting for a friend. He has a Black 03 cobra with the HPP racing Twin turbo kit installed. The body has has less than 25k on it other than that everything else has less than 6k on it.The car has working A/C and heat. So far the car has made 800hp on low boost(20psi) and pump gas. We have not had it back on the dyno for the Hi boost or nitrous tunes. the car will make over 1000HP on the turbos alone. The nitrous is only there for getting the car off the line and has never been used. This car is a blast to drive and will roast the tires at any given time. Im sure im leaving some stuff out. Asking $33,000. You can call me Allen at (903) 748-4809 Or Beau (the owner) (903) 824-2878. Mods are as follows
-Turbo Kit-
-Kit has less than 1500 miles on it
-Hpp twin turbo kit with the following up grades
-62mm billet wheel Ball bearing turbos
-Sullivan Lower Intake with HPP Sheet Metal Upper Intake
-Sullivan Fuel Rails
-New Ford 80Lb injectors(good to over 1000hp)
-Turbosmart EBoost II
-Turbosmart Blow Off Valve
-Uni rev 2 step(not yet installed)
-Hpp K-member and A-arms
-Polished Hot and Cold side piping
--------------------------------
-Nitrous-
-Nitrous Outlet 4 solenoid direct port with soft line upgrade(jetted for 150hp)
-Kit is good to over a 500 shot
-Nitrous Outlet Dual bottle Bracket with dual Nitrous Outlet 10lb black bottles
--------------------------------
-Engine Mods-
-motor has less than 1500 miles on it
-Aluminum race preped block .020 over
-Arp head and main
-Probe pistons
-Stock crank and rods
-New Clevite Rod and Main Bearings
-New oil pump
-New Comp hi lift springs
-Hpp Custom turbo cams(intake and exhaust)
-All new valves
-3 angle Race valve job
-New ford gaskets
--------------------------------
-Fuel System-
-Weldon 2345 race pump(good to 2400hp)
-Weldon A2040 Regulator
-Weldon 10 and 100 micron Filters
-Weldon 14000 Fuel Pump Controller
-16 gallon trunk mounted fuel cell
- -12 braided line from tank to pump. -10 braided line from pump to fuel rails. -6 braided Return.
-------------------------------------------
-Rear End-
-Built Straight axle
-Moser 33 spline axles
-Moser full spool
-Moser C-clip elims
-Kenne Bell rear end Girdle
-New bearings
-Richmond 4.10 gears currently installed
-New FMS 3.55 gears(not installed)
-Double adjustable uppers and lowers
-Coilovers on all four corners
--------------------------------------
-Tranny-
-Tranny Is a Viper spec Built by D&D
-Ram twin disc clutch with 900 series disc
-Aluminum Driveshaft
-Pro 5.0 shifter
-Ram billet flywheel
--------------------------------------
-Misc-
-All Vacuum Lines are stainless steel braided line with black fittings
-All Fuel lines are stainless steel braided line with black fittings
-Wheels are black FR500's with polished lip
-Tires are in good shape
-Cobra R hood
-V-6 rear bumper
-Fog lights removed
-Corbeau A4 front seats
-Rear seats are installed
-Bullet mufflers with exhaust dumped before axle
-Tuned at Hpp Racing with sct chip(flip chip is installed for easy tune change on the fly)
Last edited:
