turndowns / dumps

[97cobraholder]

looking for pic of turndowns/dumps on sn95 befor and after the rearend

has ne one ever put turndowns/dumps after the rearend to get the nosie out from inside the car but still have the turndown/dump sound

i have o/r h pipe and flowmaster cat back and the tips have got to go
thanks

 

[97cobraholder]

Nothing ? Going to muffler shop tomorrow just wanna get some ideas on how to run the turndowns

 

[ZD302GT]

They look really low in this picture just because of the angle

 

[97cobraholder]

Thanks .. clean btw I thought about doing it like that but wondered if I went over the rear end and turn down it may help with the drone and smell inside the car... I want the turn down sound tho..

 

[slow2v]

 

[PSUCOBRA96]

You could try going over the axle but at that point your just about at the end of the car anyways. That far back you may not have the extra smell. Angling them slightly out may also help so that the exhaust gases do not all directly bounce off the street right back up.

 

[2rbo97svt]

What exhaust is this I like it and how loud is it ?

 

[97cobraholder]

Would the shorter pipe make it louder before axle ?

 

[slow2v]

What exhaust is this I like it and how loud is it ?

1 7/8 ARHs with 3 inch all the way back
its loud lol

that size exhuast would be overkill at the power level your at, plus very expensive

 

[2rbo97svt]

1 7/8 ARHs with 3 inch all the way back
its loud lol

that size exhuast would be overkill at the power level your at, plus very expensive

So leave it for when I make more power ? Where did you get these is there a website you could give to me just to take a look ?

 

[slow2v]

So leave it for when I make more power ? Where did you get these is there a website you could give to me just to take a look ?

1 5/8 is fine for you're power level
american racing headers .com

 

[2rbo97svt]

^ thanks brother I appreciate it . Do you have any vids of it ? I'd like to see how loud they're .

 

[Helomech74]

ARH 1 3/4" LT's, custom made 3" Xpipe to 3" Borla XR1's.
The right side was hanging a little lower, but it as since been adjusted.

 

[2rbo97svt]

ARH 1 3/4" LT's, custom made 3" Xpipe to 3" Borla XR1's.
The right side was hanging a little lower, but it as since been adjusted.

How much you paid for these and where did you get them at ? And how loud are they ?

 

[Helomech74]

How much you paid for these and where did you get them at ? And how loud are they ?

The price for the mufflers? I don't recall the price, but I bought them from Summit and they are very loud.

 

[2rbo97svt]

Ok cool thanks yeah that was my question I'll find out hopefully these make my turbo spool up a bit faster since my exhaust is crap

 

[98 Saleen Cobra]

Kooks 1-3/4 primary LT headers/ 3'' O/R Xpipe 3'' reg magnaflow mufflers

 

[97cobraholder]

Got the cats deleted $20 got rid of the tips with 2.5in turn Downs right in front of axle $10 .......I havflowmaster super 44s stock h pipe no cats = 5.0 sound at idle and low rpms / 3200+ and just screams ..... some say sounds good I don't like the flows/5.0 sound what other muffler ? Thanks

 

[2rbo97svt]

Someone told me about which exhaust will make the flow better for my turbo set up ? Someone told me in here not too long ago but I don't remember which thread it was since it wasn't mine.

 

[2rbo97svt]

Any more turndowns/dumps ?