Home
What's new
Latest activity
Authors
Store
Latest reviews
Search products
Forums
New posts
Search forums
What's new
New posts
New listings
New products
New profile posts
Latest activity
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
Cart
Cart
Loading…
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Search titles only
By:
Menu
Log in
Register
Navigation
Install the app
Install
More options
Change style
Contact us
Close Menu
Forums
Lightning Forums
2nd Generation
Truck is dead
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="wigginwilly00" data-source="post: 8974516" data-attributes="member: 58023"><p>Sorry couldn't find the cliff notes....</p><p></p><p>DD19 VERIFY FUEL RAIL SOLENOID SHUT-OFF VALVE OPERATES</p><p></p><p> * Key ON.</p><p> * Access and enter the Output Test Mode.</p><p> * Cycle output ON and then OFF several times.</p><p></p><p>Is a click felt or heard from the fuel rail solenoid shut-off valve?</p><p>Yes No KEY OFF. EXIT Output Test Mode. RECONNECT solenoid valve. GO to DD20 . KEY OFF. GO to DD23 .</p><p>DD20 CHECK VREF VOLTAGE TO FRP SENSOR</p><p></p><p> * Disconnect FRP sensor.</p><p> * Key ON, engine OFF.</p><p> * Measure voltage between VREF and SIG RTN circuits at the FRP sensor harness connector.</p><p></p><p>Is the voltage reading between 4.0 and 6.0 volts?</p><p>Yes No KEY OFF. GO to DD20 . GO to C1 .</p><p>DD21 CHECK FRP CIRCUIT RESISTANCE</p><p></p><p> * Note: Refer to the PCM connector pin numbers at the beginning of this pinpoint test.</p><p> * Disconnect PCM.</p><p> * Measure resistance of FRP circuit between PCM harness connector pin and the FRP sensor harness connector.</p><p> * Measure resistance of SIG RTN circuit between PCM harness connector pin and FRP sensor harness connector.</p><p> * Measure resistance of VREF circuit between PCM harness connector pin and FRP sensor harness connector.</p><p></p><p>Is each resistance less than 5.0 ohms?</p><p>Yes No GO to DD21 . REPAIR as necessary.</p><p>DD22 MONITOR FRP V PID WITH SCAN TOOL</p><p></p><p> * Key ON, engine OFF.</p><p> * Access FRP V PID.</p><p></p><p>Is the FRP V PID value less than 0.2 volt for NG, and greater than 4.8 volts for all others?</p><p>Yes No REPLACE FRP sensor. REPLACE PCM (refer to Section 2, Flash Electrically Erasable Programmable Read Only Memory (EEPROM) ).</p><p>DD23 CHECK FSV PWR VOLTAGE TO FUEL RAIL SOLENOID SHUT-OFF VALVE HARNESS CONNECTOR</p><p></p><p> * Disconnect the fuel rail solenoid shut-off valve at the harness connector.</p><p> * Key ON.</p><p> * Access and enter Output Test Mode on the scan tool.</p><p> * Select: ALL ON. Note: Measurement must be made within 7 seconds of activating test mode.</p><p> * Measure voltage between the FSV PWR circuit at the fuel rail solenoid shut-off valve harness connector and battery negative post.</p><p></p><p>Is the voltage reading greater than 10.5 volts?</p><p>Yes No GO to DD23 . KEY OFF. REPAIR open circuit.</p><p>DD24 CHECK GROUND CIRCUIT FOR OPEN IN HARNESS</p><p></p><p> * Measure resistance between the ground circuit at the fuel rail solenoid shut-off valve harness connector and battery negative post.</p><p></p><p>Is resistance less than 5.0 ohms?</p><p>Yes No REPLACE fuel rail solenoid shut-off valve. REPAIR open circuit.</p><p>DD25 CHECK VREF VOLTAGE TO FRP SENSOR</p><p></p><p> * Disconnect FRP sensor.</p><p> * Key ON, engine OFF.</p><p> * Measure voltage between VREF and SIG RTN circuits at the FRP harness connector.</p><p></p><p>Is the voltage between 4.0 and 6.0 volts?</p><p>Yes No KEY OFF. GO to DD25 . VREF is out of range. GO to C1 .</p><p>DD26 CHECK FRP CIRCUIT FOR SHORT TO SIG RTN, VREF, OR PWR GND IN HARNESS</p><p></p><p> * Note: Refer to the PCM connector pin numbers in the beginning of this pinpoint test.</p><p> * Disconnect PCM.</p><p> * Disconnect scan tool from DLC.</p><p> * FRP disconnected.</p><p> * Measure resistance between FRP and SIG RTN circuits at the PCM harness connector.</p><p> * Measure resistance between FRP and VREF circuits at the PCM harness connector.</p><p> * Measure resistance between FRP circuit at the PCM harness connector and battery negative post.</p><p></p><p>Is the resistance greater than 10,000 ohms?</p><p>Yes No REPLACE PCM (refer to Section 2, Flash Electrically Erasable Programmable Read Only Memory (EEPROM) ). REPAIR short.</p></blockquote><p></p>
[QUOTE="wigginwilly00, post: 8974516, member: 58023"] Sorry couldn't find the cliff notes.... DD19 VERIFY FUEL RAIL SOLENOID SHUT-OFF VALVE OPERATES * Key ON. * Access and enter the Output Test Mode. * Cycle output ON and then OFF several times. Is a click felt or heard from the fuel rail solenoid shut-off valve? Yes No KEY OFF. EXIT Output Test Mode. RECONNECT solenoid valve. GO to DD20 . KEY OFF. GO to DD23 . DD20 CHECK VREF VOLTAGE TO FRP SENSOR * Disconnect FRP sensor. * Key ON, engine OFF. * Measure voltage between VREF and SIG RTN circuits at the FRP sensor harness connector. Is the voltage reading between 4.0 and 6.0 volts? Yes No KEY OFF. GO to DD20 . GO to C1 . DD21 CHECK FRP CIRCUIT RESISTANCE * Note: Refer to the PCM connector pin numbers at the beginning of this pinpoint test. * Disconnect PCM. * Measure resistance of FRP circuit between PCM harness connector pin and the FRP sensor harness connector. * Measure resistance of SIG RTN circuit between PCM harness connector pin and FRP sensor harness connector. * Measure resistance of VREF circuit between PCM harness connector pin and FRP sensor harness connector. Is each resistance less than 5.0 ohms? Yes No GO to DD21 . REPAIR as necessary. DD22 MONITOR FRP V PID WITH SCAN TOOL * Key ON, engine OFF. * Access FRP V PID. Is the FRP V PID value less than 0.2 volt for NG, and greater than 4.8 volts for all others? Yes No REPLACE FRP sensor. REPLACE PCM (refer to Section 2, Flash Electrically Erasable Programmable Read Only Memory (EEPROM) ). DD23 CHECK FSV PWR VOLTAGE TO FUEL RAIL SOLENOID SHUT-OFF VALVE HARNESS CONNECTOR * Disconnect the fuel rail solenoid shut-off valve at the harness connector. * Key ON. * Access and enter Output Test Mode on the scan tool. * Select: ALL ON. Note: Measurement must be made within 7 seconds of activating test mode. * Measure voltage between the FSV PWR circuit at the fuel rail solenoid shut-off valve harness connector and battery negative post. Is the voltage reading greater than 10.5 volts? Yes No GO to DD23 . KEY OFF. REPAIR open circuit. DD24 CHECK GROUND CIRCUIT FOR OPEN IN HARNESS * Measure resistance between the ground circuit at the fuel rail solenoid shut-off valve harness connector and battery negative post. Is resistance less than 5.0 ohms? Yes No REPLACE fuel rail solenoid shut-off valve. REPAIR open circuit. DD25 CHECK VREF VOLTAGE TO FRP SENSOR * Disconnect FRP sensor. * Key ON, engine OFF. * Measure voltage between VREF and SIG RTN circuits at the FRP harness connector. Is the voltage between 4.0 and 6.0 volts? Yes No KEY OFF. GO to DD25 . VREF is out of range. GO to C1 . DD26 CHECK FRP CIRCUIT FOR SHORT TO SIG RTN, VREF, OR PWR GND IN HARNESS * Note: Refer to the PCM connector pin numbers in the beginning of this pinpoint test. * Disconnect PCM. * Disconnect scan tool from DLC. * FRP disconnected. * Measure resistance between FRP and SIG RTN circuits at the PCM harness connector. * Measure resistance between FRP and VREF circuits at the PCM harness connector. * Measure resistance between FRP circuit at the PCM harness connector and battery negative post. Is the resistance greater than 10,000 ohms? Yes No REPLACE PCM (refer to Section 2, Flash Electrically Erasable Programmable Read Only Memory (EEPROM) ). REPAIR short. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Lightning Forums
2nd Generation
Truck is dead
Top