are you still seling parts, I know this is a old post.
Parting out ENTIRE CAR 03 2.6 Kenne Bell Cobra, DSG, lots of mods
- Thread starter sixpackstang
- Start date
still have the radiator cover? how much in shipping to 91709?
Bumper was trashed.
Sorry for the delay, replied to your PM.
Sold entire wiring harness.
Yes I am, replied to your PM.
Sorry for the delays everyone. I travel unexpectedly for work from time to time!
Sending PM.
The valve covers are chrome, they were the $500 Blue Oval Ind ones. Coil covers are not chrome, they are stock painted flat black. However I'm keeping w/engine for now simply because I don't want the engine sitting with the heads uncovered.
how much for just the block?
Do you still have the rods and pistons ? PM Please?
Do you still have the rods and pistons ? PM Please?
I still have the whole long block in tact. Pistons/rods/crank are still inside. Oil pan/complete heads/timing chain cover/some pulleys/accessories are on it. I will be loading some better pics tonight, and everything you see is what will come with it. Looking for $3000 as it sits.
This is it, everything listed here is all that is left from the car!
ENGINE: Has 35,xxx miles on it. Was stock until Kenne Bell was put on around 28K. Also put the EvenFlow cooling mod on at that time. The engine ran great, had no problems and NO head tick. This is the long block only, most of the parts for an eaton swap were sold off...intercooler, h/e and all hoses, intercooler pump, pulleys, lower intake, Does still have oil pan, chrome cam covers, coil covers (not shown in pics) coils, oil cooler, etc. Still has timing chain cover and crank pulley/bracket.
$3300 + freight
SALE: buy it before march for $3000!
Chrome cam covers look a little funny in the pics, its just cause its cold out, they shine up nicely.
Now parting out IRS!
Everything good except passenger side knuckle and tie rod.
IRS frame craddle $100
All 4 control arms $200 / $50 each
Knuckle $125 (driver only)
sway bar $60
ABS sensors $25 ($50 for front and rears)
Complete Halfshafts with CV joints $200 each
Differential $300 (Does not have bolts, sold the diff cover and longer bolts)
Drivers tie rod & ends $30
Max Motorsports IRS subframe bushings + 14mm bolts $25
Max Motorsports Diff bushings (urethane) $25
OTHER STUFF THAT IS LEFT:
2 of 4 SSR GT3 wheels, Satin, one 18x9 & one 18x10.5 - $400 + shipping
SSR front:
SSR rear:
FPDM $35
ABS Pump $200
Master Cylinder $100
A-Arm (Drivers side) $50
Hood Latch $15
Starter $65
Wiper Motor $20
Rear Bilstein struts $100
Front Sway Bar $60 (has bushings, no brackets)
Steering wheel/column with keys $150
Steering shaft $45
Fuel filler neck $40
Wiper arms $25
One good fog light $30
Dome light $10
MAC air filter/chrome cover $40
Dash pieces:
Gauge cluster surround $20
Left and right vents in good shape $20
Defroster pieces $20 (all 3)
Heater A/C controls/knobs $20
Door seals $25 each
Aftermarket scoops $50
Door arches $25 each (passenger side is scraped up a little, see second pic)
Radiator cover $40 (some slight scuffs, ok condition)
1/4 windows, C-pillars, all moldings $300
Mach 460 speakers $100
TPS sensor, Intake air temp sensor, Boost sensor, O2 sensors, IAC module, Fuel shut off, headlight switch, gas cap, transmission shifter thingy: Make offers
Drivers Door $200 (no interior panels, wiring. Has handles, window/motor)
(no pic at the moment)
Things that are Sold or damaged, DO NOT HAVE:
Seats - $600 SOLD
Lower Billetflow idler pulleys - $100 SOLD
Steeda Snub Idler pulley, 100mm - $100 SOLD
Door Panels with custom "SVT" inserts - SOLD
Carpet, headliner, 1/4 window plastics, back dash, center console - SOLD
MGW Shifter - SOLD
H&R Race lowering springs (all 4 good) - SOLD
Reichard Racing adjustable belt tensioner - $300 SOLD
T-56 with stock shifter, Spec 3+ clutch & 26 spline input - $1200 SOLD
SLP loudmouth exhaust (1 tip scratched/dented) - $300 SOLD
SLP catted X-pipe with hollowed cats (ohio requires them for echeck) - $200 SOLD
Powerslot rotors - $225 SOLD
Billetflow diff brace - $140 SOLD
Gas tank/hat - $400 SOLD
Guage cluster - $150 SOLD
Radio A/C bezel - $40 SOLD
Spare tire/jack/iron/big plastic nut - $70 SOLD
Battery tray/bolts - $10 SOLD
Glove Box - $30 SOLD
Rear trunk/spoiler - $500 SOLD
Mirrors - $150 SOLD
CPU - $200 SOLD
Engine Wiring Harnesses - $275 SOLD
Front and rear brakes - $225 SOLD
Front spindles/hubs - $100 SOLD
MGW Billet silver cupholders and cig lighter - $75 SOLD
Power Steering Rack - SOLD
Mach 460 Head unit - SOLD
stock sidescoops in scorch red - $85 SOLD
Clutch/Brake/Gas pedals - $115 SOLD
Entire Wiring Harness out of car. Body/Dash/Trans/Doors/etc. SOLD
Air bags - $450 for the set SOLD
Energy Suspension mounts
Hood
Front & rear bumpers
Passenger side skirt
Passenger door
Passenger tail light
Headlights
Drivers seat
Drivers side skirt
*KENNE BELL KIT IS SOLD*
1. 2.6L Kenne Bell, black with polished intake plenum and various pulleys
2. Accufab TB, polished (noticed dent after removal, adj price accordingly)
3. SCT Big Air 2800 MAF
4. CPR Fuel Rails (SC clearanced)
5. 8an Fuel line kit with filter and all fittings needed
6. 60 lb injectors with adapter plugs
I dont know if this was listed, However is the peddle assembly still available?
Tranny wiring harness?
Tranny ecu? (if it has one)
Let me know. If you do how much shipped to 90640.
Thanks
do you have the trunk 3rd light strip ? lmk, if so and if is in one piece, thanks I might also need passenger side a/c vent [by door]...
Wondering if you have the d/s interior windsheild pillar moulding if so pm me a price shipped to 10994
Sold, sold and doesn't have one.
The 3rd brake light was long gone with trunk.
I do still have the A/C vent you are looking for. All the tabs inside vent are in perfect working order. $20 shipped.
Sold it already.
If you start to part it out, I'll take those valve covers when they are avaiable. Thanks
ttt
interested in the door seals. Still have em?
PM sent
Users who are viewing this thread
