NJ 98 Cobra shortblock, 302 engine, exhaust, engine parts, crank, Fox stuff

[95PGTTech]

96 Cobra radiator, works fine customer went to a new shiny aluminum one. Since I have the thread up I'll see if I can get him a few bucks. $20 picked up.

AJE motor mounts for 4.6. Modified to ACTUALLY fit.

98 Cobra timing cover $20

Maximum Motorsports K member brace for Fox $20

BBK 70mm EGR plate $20 or trade for 70mm EGR delete

98 Cobra A/C compressor $10

98 Cobra oil pan, pickup tube $20

Fox (88LX) K member and A-arms $20

Fox rad (customer went shiny) $10

Canton windage tray $50 installed never ran the motor. I have most but not all of the nuts/studs, but after how much of a pain they were to install I recommend you use the stock bolts anyway.

10spline clutch disk I believe it's a spec $10

Generic chrome 302 valve covers $20

302 long tubes (BBK). smashed the shit out of a couple of the primaries these were a sacrificial set to send out to a header builder. $40 as is, replace a few tubes or run them as is

4V O/R H pipe no 02s $60

19?LB stock injectors from 95GT $20

MAC rolling tool cart, works great like I said just trying to get stuff out of garage have two other carts. Top can be used as a table or opens to a drawer. One extra drawer underneath, and bottom of cart has storage. All wheels and wheel locks work great. Sorry, do not have the key to this cart.

LINK - Mac Tools Online Store - MB100UC

Looking to get $100 out of it, that includes the Craftsmen 1/2" impact gun (new, never used) and the HF tire inflator with gauge, both with fittings for 3/8" air hose.

 

[95PGTTech]

Forgot to mention 302 HO engine pulled from wrecked 95GT, showed 85K on cluster, bought it as a backup thinking my 94 was on its way out. Longblock. Your typical complete longblock valve covers to oil pan minus the pan and pickup. Has front timing cover and water pump still on motor. I saw it run before purchasing. $100

 

[F8L BYT]

steering column gauge pod for 94+ cars? It looks like it is, if so will you ship that since it is small unlike the engine.

Also on the engine, so did you replace all the bearings and seals etc in there since it had the 15% loss on #8? What all is new on the engine etc

 

[95PGTTech]

Yes, 94+.

Those were the numbers when the car was still in the car. I pulled it out and did the work to it but ended up deciding to swap to a LQ9 before reinstalling this one. Block, crank, rods, pistons, rear plate, all as pictured. All new FRPP piston rings bearings on mains and rods, thrust washer, rear main, etc. The oil pan and pickup listed is the one off that motor.

 

[lowonfuel]

cobra block

It looks like you live in sourthern PA, correct? If you live in northern PA I'd come pick up that shortblock tomorrow

 

[95PGTTech]

It looks like you live in sourthern PA, correct? If you live in northern PA I'd come pick up that shortblock tomorrow

central Jersey, I need to update my junk (about 10 mins from that spot though). compared to other prices on here, that's a $600-$700 shortblock, plus a free stand, come get it, it won't last.

or if you are a real serious buyer and not a tire kicker, PM me a price offer to have me meet you somewhere halfway.

GAUGE POD IS SOLD

 

[95PGTTech]

Morning bump

 

[95PGTTech]

bump modular shortblock is gone

 

[95PGTTech]

bump

 

[crysalis_01]

Do you have any more of the A/C system for sale? If so I'm very interested in purchasing things like lines/hoses, A/C condenser, A/C evaporator, in addition to the compressor you have there.

 

[95PGTTech]

I have a lot of it, possibly all of it, but I can't see how I would get that to Wyoming undamaged and worth the effort.

 

[crysalis_01]

I have a lot of it, possibly all of it, but I can't see how I would get that to Wyoming undamaged and worth the effort.

I fully understand that there are risks in shipping. I'm fully willing to take those risks. I'm prepared to try and make this transaction worth while. I'll be PMing you in a moment with a negotiable offer.