Home
What's new
Latest activity
Authors
Store
Latest reviews
Search products
Forums
New posts
Search forums
What's new
New posts
New listings
New products
New profile posts
Latest activity
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
Cart
Cart
Loading…
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Search titles only
By:
Menu
Log in
Register
Navigation
Install the app
Install
More options
Change style
Contact us
Close Menu
Forums
Cobra Forums
The Terminator
Driveline
Just wanting to double check my 26 spline input shaft install
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="JDUB348" data-source="post: 13764967" data-attributes="member: 125421"><p>Ok so i just finished up torquing down everything. I'm getting very little to no end play. I can pull on it as hard as i can and the largest reading i was getting was .001 for end play. The input shaft spins freely in both directions with a small amount of side to side play. Do you all think i'm good to go? Input shaft is a Tremec 26 spline.</p><p></p><p>I followed what the user in the 2nd post in this thread did:</p><p></p><p><a href="http://www.svtperformance.com/forums/driveline-216/902440-t56-input-shaft-end-play.html" target="_blank">http://www.svtperformance.com/forums/driveline-216/902440-t56-input-shaft-end-play.html</a></p><p></p><p>I installed a .042 shim instead of the stock shim. I have the same exact setup as that guy, so i figured more then likely it would also work for me. Ill quote his post incase some body doesnt want to click:</p><p></p><p><strong>2001asp:</strong></p><p><em>"I had to go from a .038 to a .042. I put all my weight up and down. The shaft still spins freely, but virtually no in and out movement. To me, I did set up the guage and measured the in and out movement and found that you could get tons of different outcomes depending on how hard you yanked on the shaft. Promotion told me their secret and I went with that. .038 to the .042 and call it a day. Every car is different. The shaft I bought was a Tremec 26 spline."</em></p></blockquote><p></p>
[QUOTE="JDUB348, post: 13764967, member: 125421"] Ok so i just finished up torquing down everything. I'm getting very little to no end play. I can pull on it as hard as i can and the largest reading i was getting was .001 for end play. The input shaft spins freely in both directions with a small amount of side to side play. Do you all think i'm good to go? Input shaft is a Tremec 26 spline. I followed what the user in the 2nd post in this thread did: [url]http://www.svtperformance.com/forums/driveline-216/902440-t56-input-shaft-end-play.html[/url] I installed a .042 shim instead of the stock shim. I have the same exact setup as that guy, so i figured more then likely it would also work for me. Ill quote his post incase some body doesnt want to click: [B]2001asp:[/B] [I]"I had to go from a .038 to a .042. I put all my weight up and down. The shaft still spins freely, but virtually no in and out movement. To me, I did set up the guage and measured the in and out movement and found that you could get tons of different outcomes depending on how hard you yanked on the shaft. Promotion told me their secret and I went with that. .038 to the .042 and call it a day. Every car is different. The shaft I bought was a Tremec 26 spline."[/I] [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Cobra Forums
The Terminator
Driveline
Just wanting to double check my 26 spline input shaft install
Top