So since I've done a bunch lately I thought I would throw up a little how-to on this. It's very simple and easy, and I know almost all of you probably already know how to do this, but I thought I would show it anyways
So the first step is cutting the braided line...measure out the length you need the hose and then mark it off...as you can see I was going from stainless to the nylon line so I just used the old piece for reference
Next you need to get some electric tape...place the tape so that the line you marked off where you need to cut is exactly in the center of the tape...then wrap the hose about 4-5 time TIGHTLY. This matters even more when you have stainless steel lines
Next get out your dremel or saw tool of your choice.
Grab some safety glasses
And some gloves
Now the main thing here is the cut needs to be as STRAIGHT and CLEAN as possible...yet again this matters even more for the stainless line. If you are doing stainless line I suggest using a vise to hold the line while you cut with two hands, or use a table saw-type device where the hose can be held and the cut can be made quickly. As you can see I was able to hold the line on the edge of my workbench with one hand and cut with the other...it's much easier when working with the nylon hose.
After this is finished comes the fun part (sarcasm). Unscrew the back end of the AN fitting. Now the easiest way to do this is to use a vice to hold the line. Hold the line and push/twist the an backing onto the hose in a clockwise fashion....again this is much more difficult with the stainless line. I kept the electrical tape on as it gives it a more snug hold. With the stainless line make sure you keep the electrical tape on so the metal wires don't start to fray out. You don't have to have the electrical tape on there for the nylon, but I kept it.
As you continue you will see progress
Almost there
Now you are done when the hose end is touching the bottom end of the screw area. This one is almost done, needs to be pushed in a little more
Once you have the hose pushed in far enough, take the other end of the fitting...I suggest using a little wd-40 on the inside of the ribber hose as lubricant. Push in the fitting while holding the HOSE...dont push on the backside of the fitting already on the hose as it will pull is away from the hose itself. Start to screw the cap on. Once it becomes too difficult to hand turn, grab a couple wrenches. I used a big and little "monkey" wrench. Hold the piece that is attached to the line with one wrench and use the other wrench to screw in the top piece of the fitting.
Tighten it down until it comes too difficult....I even lined mine up...this is what it looks like when finished
And here is my new fuel rail crossover line finished
Hope this helps out some of you guys if you were wondering!! :beer:
So the first step is cutting the braided line...measure out the length you need the hose and then mark it off...as you can see I was going from stainless to the nylon line so I just used the old piece for reference
Next you need to get some electric tape...place the tape so that the line you marked off where you need to cut is exactly in the center of the tape...then wrap the hose about 4-5 time TIGHTLY. This matters even more when you have stainless steel lines
Next get out your dremel or saw tool of your choice.
Grab some safety glasses
And some gloves
Now the main thing here is the cut needs to be as STRAIGHT and CLEAN as possible...yet again this matters even more for the stainless line. If you are doing stainless line I suggest using a vise to hold the line while you cut with two hands, or use a table saw-type device where the hose can be held and the cut can be made quickly. As you can see I was able to hold the line on the edge of my workbench with one hand and cut with the other...it's much easier when working with the nylon hose.
After this is finished comes the fun part (sarcasm). Unscrew the back end of the AN fitting. Now the easiest way to do this is to use a vice to hold the line. Hold the line and push/twist the an backing onto the hose in a clockwise fashion....again this is much more difficult with the stainless line. I kept the electrical tape on as it gives it a more snug hold. With the stainless line make sure you keep the electrical tape on so the metal wires don't start to fray out. You don't have to have the electrical tape on there for the nylon, but I kept it.
As you continue you will see progress
Almost there
Now you are done when the hose end is touching the bottom end of the screw area. This one is almost done, needs to be pushed in a little more
Once you have the hose pushed in far enough, take the other end of the fitting...I suggest using a little wd-40 on the inside of the ribber hose as lubricant. Push in the fitting while holding the HOSE...dont push on the backside of the fitting already on the hose as it will pull is away from the hose itself. Start to screw the cap on. Once it becomes too difficult to hand turn, grab a couple wrenches. I used a big and little "monkey" wrench. Hold the piece that is attached to the line with one wrench and use the other wrench to screw in the top piece of the fitting.
Tighten it down until it comes too difficult....I even lined mine up...this is what it looks like when finished
And here is my new fuel rail crossover line finished
Hope this helps out some of you guys if you were wondering!! :beer: