dash lights

[01whiteL]

welll seems as though last night the dash(speedo/tach area) began flickering and eventually just stopped lightning up. So it was a pain driving anywhere last night having to turn on the cab light to check speed etc. Anyone else had this happen? Everything else lights up when I turn on the lights(radio lights/ a/c / etc.)

I've checked fuses n such but really dunno where to start.

Any help would be appreciated:beer:

 

[Taunto]

check fuses then if thats not it it could be a short somewhere.

 

[01whiteL]

check fuses then if thats not it it could be a short somewhere.

I've checked the fuses.... well this should be fun lol.

 

[smallz5.4]

omh out everything!!! Thats what I would do.

 

[blownsvtlightning]

cluster is not servicable if it has power to the Illum circuit, then the indiglo has failed and the cluster will have to be replaced. about 400 bucks from Ford.

 

[MaCaY]

there is a fuse in cluster that went off, im preaty sure that wat it is......do serch there is a thread about it somewhere

 

[01whiteL]

there is a fuse in cluster that went off, im preaty sure that wat it is......do serch there is a thread about it somewhere

looked everywhere.... can't find the damn thread!

 

[01whiteL]

cluster is not servicable if it has power to the Illum circuit, then the indiglo has failed and the cluster will have to be replaced. about 400 bucks from Ford.

cheaper to go blue it seems..... lol


Thank you for the help!

 

[JollyGiant]

F150online Forums > Other F-Series Trucks > Lightning > EL Dash light repair

Author Thread - fcmiller
Junior Member
Vehicle: 1999 FORD F150 Flareside Lightning

EL Dash light repair
In a previous append I was lamenting the fact that my electroluminesent dash lights had failed, as has happened to many of you, and the only apparent remedy was a new gauge cluster. Well lucky for us that is not necessarily the case. This fix costs less than $5 and about three hours labor.

Much better than $400 for a new cluster and $150 labor and programming fee.

The EL gauge face in a Lightning is activated, or "driven", by an inverter circuit that boosts the truck's 12 volt system up to approximately 120 volts. The circuit also takes the DC signal and pulses it to approximately 400 hz. Most of these types of circuits are protected by a fuse and, fortunately for us, so is this one. Let me make clear that this is not one of the fuses that is in the access panel under the dash or under the hood. This fuse is in the inverter circuit.

The inverter circuit (board) is packaged seperately inside the gauge cluster and can be removed and repaired. You will need to remove the cluster from the vehicle. Before you do any work disconnect the (-) ground side of the battery. You will need to remove the black dash plate around the stearing column, the headlight switch, the black dash panel that the headlight switch mounts into, the large dash panel above the instument cluster and the black circular panel around the radio control panel. The headlight switch is easy to remove but tricky, you need to know how. Turn the headlight switch knob to the "on" position. Pull the knob out like you are turning on the fog lamps. Look on the underside of the knob and you will see a small square access hole. Inside that hole is a snap that needs to be released. Insert a tooth pick into the hole while pulling out on the knob. Be carefull, the snap is fragile. The knob should slide off. The knob is now used as a tool to remove the headlight switch. Turn the knob 180 degrees and place it back on the switch stem. Turning the knob will disengage the hooks that retain the switch. You're past the difficult part, the rest is fairly straight forward.

After you have all the dash panels off you can loosen the cluster by removing 4 screws. At this point make sure that you are grounded to the truck. Attach a wire to a piece of sheet metal under the dash and then strip the insulation off the remaining end and put it inside your sock and make sure that the wire is in contact with your skin. The PATS module in the cluster is ESD sensitive. You don't want to go to all the trouble of fixing the inverter but zap the security module in the process.

At this point you need to remove the cable that operates the shift indicator dial in the cluster. A small black cable runs from the bottom of the cluster down underneath the steering column and then attaches to a hook that is attached to the transmission shift lever. Disconnect the cable from the shift lever. Disconnect the two wiring harness connectors and the vaccum line for the boost gauge. The rubber boot that attaches the vaccum line was suprisingly difficult to remove but if you turn it a bit while pulling, it should come off of the gauge barb.

At this point the cluster should lift out of the dash. Place the cluster face down and remove the white plastic back cover. You should see a three wire connector next to where the boost gauge fitting is. This connector is for the inverter module. Disconnect the inverter connector and the connector for the odometer and
remove the cluster board.

Place the board on something soft like foam rubber or a conductive ESD bag if you have one. Remember this board must be protected from static charges or your security module is toast.

Remove the plastic panel that covers the inner gauges. Try not to let the clear plastic front lense or the gauge face seperate. All you want to remove is the white panel. When the panel is removed you will see that the three wire connecter leads go to a black plastic cube attached to the inside of the panel with two screws. This is the inverter. Disconnect the two wire connector from the EL panel and remove two screws. Luckily FORD did not pot the whole circuit or we would be out of luck.

You should be able to see the EL driver board and all of it's components. Notice where the three wire connector wires attach to the board. Next to this attachment point is a green component that should have "LF 1/4 amp " printed on it. This is a 1/4 amp Littelfuse. Meter across this fuse and hopefully you find that it is open. This fuse is Littelfuse P/N R251.250. It is a fast blow , axial lead , 1/4 amp fuse. At this point all you need to do is buy a fuse from Newark Electronics or some other supplier and install it. I would suggest not trying to put a larger fuse in thinking that it will prevent it from blowing again. The fuse may very well have saved the coil or the transistor that chops the signal and both of those would have been much harder to replace. Put a 1/4 amp back in and if it blows again several years from now, well , just replace it again.

Good luck.

 

[01whiteL]

thankyou sir!

 

[fuzzie]

Didn't read many of the replies here Gared but you will probably have to replace the whole cluster. There have been quite a few going out and bad thing is I JUST sold mine.